I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hi
I'm starting with NRF51822. I'm going to develop a costum PCB using this chip. I'm a bit confused because searching on the forum I saw that I need a product key to use...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi all,
I am using the multi role example ( github.com/.../nRF51-multi-role-conn-observer-advertiser) to scan and advertise concurrently.
I was wondering if the scanning...
I have a 16MHz external clock oscillator to drive a micro controller in my system. Can this also be connected to the crystal input on the nRF24L01+ to drive it's clock? Should...
Hi All,
I wanted to write a patient record to glucode measurement charateristics from android Phone which supportes BLE features . How do i write a record to BLE device...
When using the OTA DFU using the button press implementation is it possible for the bootloader to require bonding? I figure I can use the preserve app data functionality built...
Just took the developer.mbed.org/.../ code and run it on the board.
But when I try to connect with my phone I get: "Device doesn't support UART. Disconnecting".
What...
Hello,
I am using the RedBearLab's BLE Shield 2.0 and I'm trying to modify the advertisement data using nRFgo studio to include manufacture data (type: xFF) for one of...
Our IC nRf51822 has an identifier "QF AA CO" (IC rev 1) The document "nRF51 Series Compatibility Matrix", Table 4, shows the maximum version of the SDK 5.2.1 and 4.4.2 SD...
Hi guys,
I install V1.6 nRF ToolBox apk in my Android phone, and want to do the DFU operation.
When the device in DFU status, I select the target HEX file but it shows me...
We are configuring the watchdog like this:
// Watchdog
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Run << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Run << WDT_CONFIG_SLEEP_Pos...
So I've got this long characteristic which takes several read operations with offsets to read it completely. Idea is to have it refreshed only after the client has read it...
Hi all,
I've have written a debug version of our application firmware to catch any and all error seen during operating. The most common one I see is NRF_ERROR_BUSY stemming...
Hello,
I am doing some tests with the Heart Rate Service Sample Application for the nRF51822 evaluation board (PCA 10001). Inside the ble_stack_init(), there is this call...
