Hi,
I am sending data from Android phone in every 200 ms to nRF8001. But sometimes I found there is a 50 ms or 100 ms delay. It looks like nRF8001 spending some time in...
Hello,
I'm starting a new nRF51 project on mbed for a custom board. I wish to know what is the "cleanest" way to define pinout (what file to edit) ?
Thank you
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
Hi，
i defined spis rx and tx buffer length at:
#define HUB_SPIS_RECV_BUFF_SIZE 1024
#define HUB_SPIS_SEND_BUFF_SIZE 1024
because the rx data length will be vary...
Hello nordic
I use ble to create custom services, I want to create an embedded system that can create and send and receive data. I am using sdk version 14.2.0 and what...
Hi,
Im currently designing a custom pcb using nrf52 reference design available here . In my design, I have to connect the ground of two analog signals to VSS of nrf52832...
I tried Blinky blank application on PCA10040 by IAR. By pressing "Download and debug", everything is fine, I added RTT debugging information and can see it from RTT viewer...
I Have an issue trying to flash a nrf52832 custom board.
Something extrange happens because when I download an example from keil that blink a led(gpiote_pca1036(nrf52 PCA10036...
We are using s110_nrf51_8.0.0_softdevice.hex soft device and nRF51 SDK v10.0. We have below questions in case of soft device assert scenario.
In what scenario's soft...
Hello,
I am working with the example of PDM example on the nRF52832.
And over this I would like to use the drv_speaker. I put all the files from the Thingy 52 example...
On a system using an NRF52832 with S132 softdevice (without no external LFCLK XTAL), in low power mode via sd_app_evt_wait() - we see a nominal current of ~3uA with a periodic...
Hello Nordic,
Can you share pdf of nRF91 sneak peek presentation.There is an audio problem on video.
Best regards,
Marcio
www.nordicsemi.com/.../Low-power-cellular-IoT...
hi team,
i am having a doubt. i had created a service for connection interval which is 0x1528. with read and write properties. in that we can set value from 100ms to 10240ms...
I would like to ask for any information regarding the near-future plan for the nRF SDK for Mesh.
Are these features planned? And if so, when would they be implemented?...
nRF52832
There are three ways of working with the clock registers, a hardware access layer macro set, the nrf_drv_clock.c/h, and direct register access.
What is the...
I am implementing Device Firmware Update using BGLib on C# using BLED112. When i am writing on the DFU Data point on Peripheral (which is a Nordic's nrf51 chipset), i need...
hi,everyone.
version:sdk10.0
i know the nrf51822 system running order is: softdevice->bootloader->app.But i have a question when i am reading bootloader. If the program...
I have a question about the wait_for_flash_ready routine in the nrf_nvmc.c file.
static inline void wait_for_flash_ready(void)
{
while (NRF_NVMC->READY == NVMC_READY_READY_Busy...
