Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi Engineers !
We are going to implement AES CRYPT/DECRYPT Protocol over BLE to add some additional protection against HACKing with use of HW " 6.6 CRYPTOCELL" the MODULE...
Hi, I want to use a couple of 0805 resistors, hook them up in tandem to 220V AC power source, and then do some zero-crossing detection.
I know I know, this totally isn't...
Is it possible to use the Segger SystemView software with the NRF52832? When attempting to use SystemView, I get an error "RTT Control Block not found". It's possible to enter...
Hi,
I can't find information what shape of spectrum I should expect from test mode (CONT_WAVE = 1, PLL_LOCK = 1). At the moment I get main spike with smaller symmetrical...
I'm running into an issue when trying to use the timeslot API for advertising while concurrently scanning. Scanning is using a 100 ms interval with 50 ms window and initialized...
Hi!
I have created a project for nRF52 DK in Segger Embedded Stuido. I wanted to creat it for nRF51 but there was no eamples to start from in the sdk that supports pca10030...
I used the example ble_app_cts(SDK12.3),but when I connected the board(NRF52832) ,I did not find the cst service,Now,I want to know why I did not find the service and where...
Hi everyone.
I'm currently working with NRF SDK for Mesh v2.0.1, SDK v15
I'm adding light switch provisioner to light switch client example.
In file provisoner_helper...
I have to develop an appropriate driver circuit for a DC Motor, the Motor is to be connected to the IoT node Nordic Thingy 52, which can be switched on and off with the button...
Hi all, I'm developing a project based on nrf52832 and a custom board, what I want to know is if it's correct the actual power consumption.
The custom board has the following...
Hello, I am still using S132 version 2.0.0-7.alpha with Keil uVision V5.21.1.0
Should I move to newer version. Why uVision doesn't see new S132 versions in the pack installer...
hi hi hi everyone
i'm wondering can us use HCI protocol to develop our product without using by the softdevice as you know by using the softdevice we can just interact with...
Is there a way to turn off the BLE NUS service once we are done with and turn it back on when we need it? I tried
Seems to have had no effect. I am using the BLE NUS service...
Hi Sir,
I use microcontroller to control the nrf8001 to broadcast packet every 8 second.
I measurement the current, found nrf8001 take more power in sleep mode(red part...
