Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
nrf52832dk pca 10040 board
besides ports bits and dir setup and baudrate, etc ...
this is part of my uarte init funct (pDev = 0x40002000)
pDev->TXD.PTR = (uint) TxBuf...
I just bought a nrf51 dk to master this wonderful SoC series.
For now I intend to keep my research and studies with Bluetooth 4.1, but would like to prepare for a jump...
Will uarte interrupt call NRF_LOG_INFO, will run away the possibility of the processor? backend uses RTT
I set uarte receive dma buffer to 10, then the sender to use the...
Hi all, we have a problem with a project based in nrf52832 and a custom board. The project is based in "ble_app_uart" example, and also we have the following sensors:
Accelerometer...
hiii friends,
i have developed new board using nRF52832 xxAA. i am dumping code in this using nrf52 DK and it is working fine but when i am removing power from this and...
Hi, I want to confirm if the Mesh packet is a "special" form of advertising packet or it is completely different, i.e. all the headers and addresses etc are changed.
By...
Hi, I am using Keil to build programs less than 32 KB in size. All the example program from the SDKs work and I have read that should be the case because they are all under...
Hi all,
I'm going to use the latest SDK version of nrf51822 for my current project. Can you please help me to choice the right one for my development?
I want it as peripheral...
Hi all ,
I am learning theory about BLE . I'm exploring the relationship between layer . But I am quite difficult to understand the package structure from upper layer to...
Hi,
My config :
Board NRF52DK
SDK 14.2
Segger ES Release 3.30
SEGGER J-Link V6.22a
macOS 10.13.1
I want to use RTT to debug my code. As a starting point I've...
The manual clearly states that the external HFXO should be 32MHz. However, if one would like to have precise 16kHz on the PDM and I2S interfaces a 32.768MHz crystal is required...
I know that RF52840 could act simultaneously as the Advertiser\Peripheral and Observer\Central and I saw Nordic's recent demo video of BT + Thread co-existence. However, it...
I am having very limited knowledge in flashing devices, infact this is the first time I was doing it, pls conider
Step 1: I bough PCA10040 and installed nRFGo software in...
I have found multiple PDFs indicating the lay-out on the nRF52-DK. However, none of them tell me anything about the size of the kit. Does anyone have a PCB lay-out with at...
