I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Continuing to port MESH into an IAR project. We would like to make logging work with IAR. Right now, we get a warning that the "format" attribute isn't supported.
Is there...
The valid master out time for <= 8 MHz is shown as tSPIM,VMO 59 ns. The valid master out time for > 8 MHz is shown as tSPIM,VMO,HS 8 ns. The latter tSPIM,VMO,HS could only...
In simple on/off example, the client can turn on several server nodes in the same group in the same time,
but in serial example mix simple on/off server, the info center...
/* Copyright (c) 2014 Nordic Semiconductor. All Rights Reserved. * * The information contained herein is property of Nordic Semiconductor ASA. * Terms and conditions of usage...
Hi there,
I aam using SDK 14 and using all sectors of FStorage. I am using all the sectors of FStorage to read and write data.
After about 24 hours, I see data corruption...
Hello,
So I'm loooking for a way to transfer relatively small quantity of data live as reliable as possible and as quick as possible between two nrf5 units and then between...
Hi,
I am using Nrf51422 DK, my need is to send file (which is placed in my computer)to the another nrf board. Tried with file operations (fopen,fgetc,etc.) in keil4. It...
While flashing program to nrf51822 device through terminal getting these error msg
ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR: persists,...
Hello, I currently using the proxy light switch exemple of the mesh SDK 2.0.1 in this configuration :
I search to have the less current consumption in the mesh client ....
Hi all,
Please find my following current measurement resuls in the pwr_mgmt example using a nRF52 preview DK and SDK 13
My setup is as follow:
SB40 is cut
SW6 is...
int main(void) { initialize(); execution_start(start);
for (;;) { (void)sd_app_evt_wait(); } }
can you explain me the execution of code flow in the main with these APIs...
Hi to all,
I am new i ble tech, i read some where that notification charactristic dose not need acknowledgement but indication need, now i want know that this acknowledgement...
Dear all developers：
I want to use whitelist on central mode，and using SDK12.3.0. I have see some call be used like this:
pm_whitelist_set（whitelist_load()）
p m_device_identities_list_set...
Hi,
We are working with SDK 15 with the HRS freeRTOS example. we did some modification to the advertising modes so that we advertise on fast mode for 1 minute and after...
Hi,
I'm using nRf52832 with SoftDevice S132 V3.0.
I found that I can exclude a bluetooth channel from the map by function sd_ble_opt_set .
But how can I tell that a...
