I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
hello,
when I use the chip nrf51822(3rd generation),I find that when I open DCDC function,the ability of chip receiving msg is weaken.the receiving distance is shorter a...
I am doing a blob read on two s130's with s120(central). I am getting BLE_GAP_EVT_CONN_PARAM_UPDATE event while doing a continuous blob read.
Some times i get BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
Can you please provide full schematic for nRF52 dev board. I looked though the documentation and there are small bits of the schematic, but I didnt find full sch...
Using a nRF51822-QFAC-A1 on the nRF51-DK I noticed unexpected behavior when starting the HFCLK and LFCLK in rapid succession. This variant reproduces the problem at startup...
I would like to have 31 bytes for my own in advertising and so far I have disabled everything except adv_flags (it still takes 3 bytes cause of length, AD type and value)...
Hi there,
just wanted to know what the practical differences between the JLINK and mbed MCU interface firmwares are.
From what I experience I can only use the UART over...
Hi,
I'm writing a service to send indications on a couple of characteristics that are part of a service. In order to determine whether indications have been enabled or not...
Hi,
Is there a smaller version of the desktop 2 firmware? I don not need firmware for NFC only ble 4.0. Also would like less complicated pairing. The 6 didgit code is unnecessary...
Hi , I tried to change the transmission power using the s110 API and tried checking if the value of the register storing the transmission power is changed or not. Following...
Hello,
I'm trying to create my own bootloader application that uses softdevice in IAR. I would like to know how to configure my project so that it writes 0x0003A000 to...
Hi all,
I've a problem using pstorage: after I execute a pstorage_clear, my ic (i have the pca10028 board) go crazy, the application I've write stop execute and I can't...
I have an application that advertises as connectable in BLE.
After connection and configuration, it should then disable connectable advertising and enable nonconnectable...
Hello,
My nRF51822 custome board has problem at first programing software with nRF51 DK. So I checked nRF51822 boot sequence and found diffence compare with nRF51422 which...
