Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I want to experiment with recording observations of the beacons with raspberry pi's.
Is there any precompiled firmware I can install on the nRF51822 smart beacon...
Working on a wireless mouse project using an Interlink micro joystick ( www.interlinkelectronics.com/MicroJoystickHDK.php) and nrf51822 ble module. Movement of the interlink...
I've read through the DM code in the S110 library of v8.1, so this question is just asking for confirmation of what I'm reading.
The device_instance_allocate function returns...
I have an old version of nRFgo Studio and nrfjprog installed on my computer (version 5.2.0.45231). I use nrfjprog from command line to flash my devices (easier than clicking...
Hi, I am developing a coin cell powered NRF51-based device that needs to keep track of reasonably accurate real time (no calendar, just number of seconds) in a long term ...
hii,
i am working on ble project where i would want to read the name and address of a slave.The example i am looking at is "nrf51_sdk_v6_1_0_b2ec2e6\nrf51822\Board\nrf6310...
Hi All,
I am trying to make a nrf51822 talk to a SPI display by using the SPI Master.
My problem is that the display does not give any output, only takes input.
The...
Hello,
I am writing an application in Qt that runs on the computer and interacts with a nRF51422 via BLE. Now I have noticed, that I have to tell the framework, which address...
How do I reset nRF51822 to shut down the debug port?
I have a custom board with a built-in battery and strong power management.
If I power up the board without the debugger...
Hi All,
My goal is to advertise the generic packets untill a GPIO interrupt occurs. So in order to achieve low power consumption I have increased the time interval of those...
bootloader.rar (/attachment/d5fd4fbbc7d37433740f6c9468f3110b)
bootloader_dfu.rar
Hi,all.i want to set same macaddress with my app in bootloader,and advertise it in bootloader...
I have a pstorage Clear and Store that I use just before calling bootloader_app_start() in my DFU bootloader code. Everything was working great testing/compiling (GCC) under...
Hi,
we'd like to use nexus 7 II(android 5.1.1) to connect nrf51822, but cannot connect if nrf51822 uses whitelist.
step 1. we send advertising packets without using whitelist...
I'm trying to build our application using GNU Toolchain and currently facing compilation issue with __asm directive; the error thrown is:
../../NRF51_SDK_v6_1/nrf51822...
I usually see a system event "NRF_EVT_FLASH_OPERATION_ERROR" when updating my device firmware. SDK says that this event indicates that the ongoing flash operation has timed...
