I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I am using arduino to sample sensor and it sends out the value to the digital pin. I want to read this digital value using nrf51dk. Is there any example using digital...
Hi Nordic Tech support team,
I have some questions about nrf51822 dfu OTA.
Nrf51822 application code can't be more than 144K，however ，my application code have 196K because...
we follow the nRF51_Series_Reference_manual v3.0, set the master SPI clock to 8M. but found when in mode 0, the MOSI change near at SCLK rise edge, not in fall edge.
our...
This should have been a very simple question. I don't want to use CTS/RTS flow control signals with my UART-USB-converter ("FTDI chip"). For that case, the document says ...
I want to highlight some items in RTT Viewer
So I tried the color control, but didn't work
This is my code.
SEGGER_RTT_printf(0, "%s[Mutex error:%u]\n%s", RTT_CTRL_BG_BRIGHT_RED...
Hello.
I am trying to port BLE serialization code to a host MCU, to say STM32F4.
I am looking through porting documentation (BTW, it is quite well documented. Well done...
According to Microsoft's instruction on HID touch device, msdn.microsoft.com/.../dn672271(v=vs.85).aspx , a HID touch device should create a report (descriptor) as below,...
Hi,
I am having a 324 byte,a 420 bytes of array stored in flash,now i am updating these array with 360 bytes. in fds_event_handler in the case FDS_EVT_WRITE i am reading...
Hi,
I'm looking for an example which combines FreeRTOS, BLE and ADC on nrf52 board(10040).
I'm able to have FreeRTOS with BLE, FreeRTOS with ADC but not everything together...
Hi,
I've read a lot of question on the forum, but I'm a lit bit confused about what I have to do to use one static passkey on the central and peripherical device. In my...
Hi There,
I'm having problems with my hardware timer appearing to stop counting or not being cleared via a short when the timer interrupt is executing.
In my application...
Hey!
I want to use the nrf51 BLE-module in some special environment.
It should be able to work with bluetooth and in addition to it with some other RF protocol (Gazell...
Hi,
I have added "DFU" functionality to my existing BLE application Test.rar .
"I am using nrf52 SDK v11.0".
I have programmed the device with softdevices (S132.hex...
