Hi DevZone Engineers,
As I am unable to access my board (Xiao BLE Sense (embedded form) with Nordic 52840 SoC) through the "Connected Devices" tab in nRF Connect, I am trying...
Hello,
I've been working on a project involving an IMU and bluetooth for a while, and had been using the IMU (LSM6DSO) on polling mode. Unfortunately, I found out that I...
Hi,
If anyone has time, I'd be grateful for a quick review of my board. It is my first board, I'm still learning, so I would like to know where am I making mistakes. It...
Hi,
when i try making a new connection with a new device using my for loop (reconnecting using the adresses that i stored in an array), i sometimes can get a warning which...
Hello!
I am working to design and build a custom PCB using the nRF7002 chip and came across this callout on the schematic diagram and wanted some clarification about it...
Hello,
I am trying to use an sdcard with the nrf54l15 DK board with the 2.9.1 sdk. However I encounter "<err> fatfs: Storage init ERROR! error: -134" when calling the disk_access_init...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Hi,
I am trying to port my Application from SDK13.0 to 14.0.
I have completed the porting. But the code is not working.
In Service initialisation there are issues...
Hello,
I use the nRF5 SDK 11.0.0 and with it we can easily build the examples with armcc from Keil, or with gcc (arm-none-eabi-gcc) from the command line using your Makefiles...
The current configuration looks as follows:
IDE: Eclipse
Toolchain: ARMGCC
SDK: SDK5_NRF_14
DK: NRF52DK-PCA10040
I am trying to port the 'bootloader_secure_ble'...
Hi,
I've combined the secure serial and ble bootloader and using it for my custom board. I tried flashing my application hex over serial using nrfutil. I get a device programmed...
Hi,
I am working on the nrf51822 board and i am only the PAC20006 board version seems to be working on it. I am using sdk 11 and soft device version s130_nrf51_2.0.1 s suggested...
Planning for Evaluation of nRF52810.
I am thinking of using nRF52 DK for this and i want to know if there is any beacon with nRF52810 which i can use for this evaluation...
Hi All,
1.One master BLE has to connect to Slave BLE, then both device should read other RSSI and sent the data through UART.sending the RSSI should be every 200 millisec...
Hello,
I try to use those functions for printing log massages on the Segger RTT terminal, but I have many problems with that.
1. How can I use this function without printing...
Hi everyone,
I am using nRF52832 kit (PC10040), eclipse and softdevice S132 V5.0.0 for developing a BLE service. I follow the service tutorial and I refer to the code from...
i want to connect raspberry pi 2 with nordic thingy 52 via ble.....while issuing connect command after gatttool -I -b Mac addr it is throwing some connection refused error...
i want to know about how nrf51822 module's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
All,
I'm relatively new with the Nordic Ecosystem and have been playing with the example projects on the nRF52 DK and have successfully gotten several examples up and running...
Using Keil v5, ARMCC 5
Pin state equals:
Level 0 - 0x00000000 - pin low
Level3 breakpoint after read - 0x00000040
Level3 breakpoint before and stepped through -...
