Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I am using custom board with MDBT53 and I'm stuck at a point where board does not even let me to connect the debugger so that I can refresh firmware.
I added MCU boot code...
Hi, I have changed Vdd from 1.8 V to 3.3 V but now I cannot flash anymore my board (nrf5340). This is the output error:
* Executing task: nRF Connect: Flash: AppCore_RHS_SD_UI_v1B...
Hi,
a couple of days ago, I had to install some STM plugins for VS Code (I'm sorry ).
In the process, the "CMake Tools" from Microsoft were also installed. I remember...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hello,
In ncs, I am working with \nrf\samples\ipc\ipc_service. I want MCUboot to build \nrf\samples\ipc\ipc_service\remote to run on nrf5340 CPUNET. When I CONFIG_BOARD_ENABLE_CPUNET...
Beginner here .. steep learning curve for Nordic ... trying a project with I2S. Took half and hour with an ESP32, but many many hours later, no joy with Nordic.
Working...
Dear Nordic Support Team,
We are currently exploring the use and potential benefits of the paEventCounter as described in the Bluetooth Core Specification 5.4, Section 4...
Hello. I use the function zb_zcl_finish_and_send_packet to send data from ZC to ZED and it works but one problem is that we're using a rather slow poll (20 seconds) to enhance...
Dear Nordic,
I have a few questions I would like to ask.
1. I would like to inquire if there is an antenna pattern for the nRF54L15DK PCB.
I have already searched through...
We have been fighting with the Distance Measurement Toolkit for a while (see other ticket ). As we needed to move forward, we started the implementation of LE Secure Connection...
