Hi, recently I have been experimenting with the channel sounding with range requestor sample on the nrf54l15dk. I have modified the reflector code to make it connect with...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up to read the potentiometer's raw value . As part...
Hello
I am testing with the lis2dh12 sensor and our custom board. I made the LCD test successfully. So I tested the lis2dh12 sensor based on the LCD code, but it failed....
Is there a comprehensive explanation of the usage of uuids_complete, uuids_more_available & uuids_solicited when to use them and how the stack behaves/uses them. I getting...
Hello
First of all, I would like to apologize if a similar question was already asked but all this BLE matter is so broad that it defeats me.
I am planning to put two...
I try to use Eclipse for my nrf project. Previously I used Keil but now, I should to use Eclipse. Anyway, I can build nordic sdk example project but when I work with main...
Hi,
I have posted the same question in the following URL.
devzone.nordicsemi.com/.../
It will be very helpful if you tell me how to get a correct MIC result by AES...
Hello,
I've got some trouble using Nordic Uart Services,
I correctly add the library to my project.
I can receive data from different devices. But when I want to...
Hi, everyone,
I develop the project on N52832 chip when the chip "plays" central and peripheral roles together.
During the running the program I need to check the advertising...
Hello. Everyone.
I'm Aaron and beginner in nRF52832.
I have some serious problems with using the nRF52832.
I'm trying "ble_peripheral\experimental_ble_app_blinky" in Keil...
Hello,
I am using 14.1.0 SDK, I implemented the custom service and characteristic,
but if adding CCCD(Client Characteristic Configuration Descriptor) with the custom value...
Hello,
I am using nrf52 and sdk12.2.2. Can I program this with bootloader and application image at once using nrf go studio?
At present I am first uploading bootloader image...
Hi,
I have 3 nrf51822 devices. Two of them act as peripheral and one acts as central. Each peripheral is used in a wheel and they are the 2 wheels of a cart. Central is...
We are trying to connect RF51822 with RaspberryPi over Bluetooth. Our aim is to get Light sensor values(lux).
Please advise how to get started with RF1822 Sensor.
*) How...
Hi there~. I tried Nordic's FFT example (SDK 14.2) with a PCA10040 board. So I tried to add that FFT related codes in the heart rate peripheral example. I use the Segger's...
Hello, I am practising and studying the beacon example on nrf52840. While reading the main code, I try to delete the log_init part, however the kit doesn't advertise. I am...
