Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
I'm attempting to use the USB MSC example (from nRF5 SDK v15.0.0) with external flash chip replaced with Winbond W25Q128FV and I see the following logs:
[00:00:00.000,000...
Hi,
I have designed a customized for nrf52832 with a trace antenna. I haven't used any low pass filter and made the changes inside sdkconfig.h file to use RC and that board...
Hi,
I'm using nrf51822 module purchased from www.waveshare.com/core51822.htm . I'm running uart over ble application example. I commented uart_init() function in main(...
Hi,
I have the following setting. I have a dongle with with a nrf52 which sensd all data received from the NUS service to the host via a uart and a FTDI. The FTDI is capable...
Hi.
I want to implement multirole on the nRF52832. I want to advertise beacon data while scanning. So, I modified ble_app_uart_c in the ble_central example. Below is a description...
Hello,
I would like to disable and enable the nus_data_handler in my code to work with several interrupts, so I need to disable that handler and then reenable that again...
hi,
I am using nRF51-DK board as external programmer to program Minewtech Minibeacon having nRF51822 chipset (QFABC1, 128KB flash and 16KB RAM).
Tools:
SDK: nRF51_SDK_10...
Hello, Is it possible to use a RedBear V2 with the DAPlink as a Bluetooth dongle, apparently, the DAPlink can function as a USB-UART bridge. I'm new to SoC and am trying to...
Hi
I am trying to load my shiny new NRF52840 dongle with a simple blinky app using the nRF Connect (v2.4.0) but I get an error stating that the 'Region starting from 0x0...
Hi,
I follow exactly the same as "Interactive mesh provisioning and configuration" and stuck at "Adding a Light Switch client (optional)" part.
Everything looks fine,...
I am working on a J-link command line.
i just want to lock a device after a write a binary file into device.
In j-link there will be option for a unlock a device like...
Hello,
I'm developing a program using nrf52832 DK and SDK V15.
I want to activate the SPI transmission when NRF_RADIO->EVENTS_END occurs using the PPI. I follow the PPI...
I am trying to connect an lcup heart rate sensor which is an analog device . i am using the SAADC example t interface it to the NRF52 board, but iam not getting the expected...