Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I am not able to connect to AWS MQTT (using sample code for AWS ) . I am getting Error code -11 every time . CA cart and keys added in code.
Same keys are working...
During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
I'm having trouble enabling BLE DFU on my firmware for the nRF52833. I'm following the steps from the Dev Academy course - FOTA over Bluetooth Low Energy . After adding the...
Hi,
I found that the NRF 54l15 can only estimate distance based on channel sounding and RSSI. On the bluetooth website it mentioned channel sounding accuracy being around...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi all,
It is a common convention to configure the I2C SCL signal to be push-pull instead of open-collector if there are no other I2C masters in the system (saves a pull...
NRF52840
S140
App based on ble_app_multilink_central.
I have tried to build a bridge between BLE peripheral and PC.
I have spend so many time on PC side app.
The...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
I have finished developing an application, utilizing the nRF 9151 DK, and I am now working on transferring the firmware to a custom board and testing it. However, when creating...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
I am currently using ncs 2.9.0 on a custom board using the internal ldo and internal clock settings. It is a simple project where I take and indicate an adc and internal temperature...
Dear Forum,
I have an nrf54l15 device and I would like to send a pure sinusoidal tone and measure the phase difference, retrieve I/Q values at the other device. This is...
Hi! I am designing a nRF54 based motion tracker that has an IMU onboard which can take an external clock signal for improved timing accuracy. Initially I had thought of just...
Hello,
I am having an issue using GPIO P0.03 as a button input in my design. Unfortunately, I did not notice that this pin is marked as a dedicated pin for the GRTC peripheral...
