hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
I tried to set up the ANCS example. It works fine. But how is it possible to set a higher MTU. I set the NRF_BLE_GATT_MAX_MTU_SIZE to 247. But the Log says after a connect...
Hello, somebody help please.. I want to implement Machine Learning using tensorflow, KNN or whatever is good for my module, that consist of Bluetooth Low Energy nRF51822 type...
I want to start with the following nRF52 ADC example .
While doing so, I found that the example is built on SDK v13 and SDK v13 doesn't have Seggar Embedded Studio support...
Hi
I successfully merged SDK for mesh v1.0.0 to nRF14.2 by following the example in https://devzone.nordicsemi.com/f/nordic-q-a/28936/merging-sdk-14-2-with-mesh_sdk .
...
nrf52832
SDK 14.2
My application is locking up, and finding the cause is proving to be difficult. I've enabled DEBUG and DEBUG_NRF and included the hardfault library...
I have an application that requires talking to 21 sensors wirelessly. The bandwidth required by each sensor is relatively small - roughly 2KB/sec. The sensors need to talk...
Hello,
The mesh lightswitch on/off example only calls 'sd_app_evt_wait' in the main loop.
I'd like to use '__WFI' instead. (Im combining some code with mesh, and i'd like...
Hello,
This case is a part of a private case. Unfortunately havent responded for few days. I believe he has days off or something, therefore I am willing to receive help...
Hi everyone,
I design own boar with nRF52810 SoC. But i dont know how to programming external. Which pins are using programming? SWDIO and SWCLK pins using programin i know...
I want to establish a BT network system which includes one pc as a central node, and 32 client nodes. I want to collect 32 client's sensor data concurrently via BT. At pc...
Written a custom script to write product model no into UICR Registers. After updating Model No, DFU was getting failed at state 6 i.e after updating init data after moving...
Hello everyone,
i know that there are many similiar questions on the DevZone but i am not able to get it work and i dont uderstand it yet. I want to flash a custom board...
I am trying to sent multiple messages from nrf52dk but it seems that i can sent only 7 even if i put a delay between messages . Any suggestions ?
for(int x =0;x < numberofevents;x...
Hello,
i am working on an app using Android to read and write an NDEF record using SDK 14 type 4 tag.
I start the process by reading the record with the following Android...
hw: nrf52dk
sw: sdk14.2, ANT/BLE "multiprotocol" HRM app example
I tried to build and run ANT/BLE HRS relay example from SDK14.2 WITH NO CHANGE IN CODE, but it doesn't...
