Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I am using the iPhone 8, BLE device (51822/51422), s130, SDK 12.3.0.
and using a bonding and passkey to connect.
However, Direct connection after disconnect For example...
Hello,
I am trying to fix the UART communication error(APP_ERROR_HANDLER(p_event->data.error_communication);).
I am sending a command(0x87,0x14,0x11,0x33,0x44) continuously...
Hi,
Sorry if this question is too simple - I tried to search existing threads before posting.
I just received the official nRF52-DK and would like to get it started, I...
Hi
i have LIS2DH working ok just having problem with the order of return values, maybe just a quick fix.
LIS2DH is running on 10Hz, low power mode, I receive interrupt...
Hi!
We are experimenting with BLE Mesh on nRF52832.
Our setup includes around 50 sensors located in a building which need to report sensor data ( 12 bytes ) in real time...
Hi,
I'm trying to configure nRF51 usb dongle as server but can't get it to advertise.
Neither 'Advertising setup..' nor 'Start advertising' option seem to do anything...
So I've been banging my head against the wall for a little bit now and this just isn't making sense to me.
I downloaded the NRF Toolbox app on my phone, and I compiled the...
I am working on SDKv14 with S132 softdevice and was trying to modify the Heart Rate Example to vary the Manufacturer Specific Data after each advertisement. After searching...
Hi,
I have recently started working on nrf52832 chip, don't have much knowledge on that. I have two chips (nrf52832) one is running on bluetooth version 5 and other one...
I'm evaluating BT5 feature using the PCA10056 preview dev kit and SDK v15.
When working with LE Coded PHYs, is the S2 or S8 version? In the SoftDevice release notes only...
Hello,
I'm testing the bootloader with SDK v.15 and I found a state when DFU won't resume (on BLE transport).
I crashed nRF Connect randomly, in that case, between the...
Hi All,
I am designing circuit to Turn ON 4 LEDs at a time based on high and low of GPIO
Supply voltage is 3.3V my doubt below circuit is fine whether it will work fine...
I try onnrf52804 (nrf52840-DK) with SoftDevice V6.0.0
----------------------------------------------------------------------------------
ble_gap_scan_params_t s_scan_params...
Hi all,
I want to use the python scripts provided in application notes in nordic documentation to run DTM example flashed into nRF52840 SoC. So when I open command prompt...
