Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
nRF52, SDK12.1, Eclipse, gcc 5.4.1, FreeRTOS, no soft-device.
I am having a problem with GPIOTE. I have six interrupts programmed on six different pins. As long as the...
hi everybody
SDK:14.2
Chip:52832AA
NRF GOSTUDIO:12.2.10
JLINK:V9.4
I use NRF GOSTUDIO to write sofedevice or app,it note:
unable to find or open the...
Hi,
I am a beginner with NRF chips, just wanted to know that Can I use different package size for Capacitors/Inductors like 603 instead of 402?
Thanks.
Hello,
Our production systems run on Raspberry Pi, which is running on ARM. Currently the nRF5x command line tools are only available on x86, which means that we need to...
After working with NRF51822, I decided to go for NRF52832, and I bought some modules that have NRF52. I am using GCC and SDK13. I installed the S132 soft device which is in...
Hi - I am using NUS (Nordic UART Service) to send raw sensors data over BLE to my PC for later processing. However, I found that I can not get a more-than-20-packets-per-second...
Hello,
I am preparing a driver for the SAADC of nRF52832; I have to acquire data from five channels; consequently - in a scanning mode.
However, what I observed is that...
Hello,
I need to read SAADC input pin of nRF52832 that is multiplexed and wonder what the optimal strategy is to implement that.
Especially: setting a ppi channel so that...
Target - NRF52832 populated on a custom PCB using SDK 14.0.0 and s132 5.0
Background - end device will be used to send logged IMU data to the cloud via a smart device,...
Hi,
This is my first post here. I hope I will follow the structure of a good question.
I want to have a sequence of defined duty cycles (let's say 4 values). The aim...
serial-rtt.zip I'm having trouble debugging SDK14.1.0 example serial using NRF_LOG with NRF_LOG_BACKEND_RTT_ENABLED using the NRF52 DK, PCA10040.
With NRF_LOG_ENABLED set...
Situation: Trying to upgrade previous versions of the SD and BL (V3.0.0) to (V5.0.0)
Problem: device power cycles after a new application is flashed to the device into the...
I have successfully managed to communicate back and forth ( message ,Temp and Humidity data) between Two Arduino Nano using NRF24L01 module. However when I am trying to receive...
Hello All,
I'm using nRF52810 with SDK 14.1 base on ble_app_uart example. where i am continously receiving the GPS data via UART i changed the uart pin configuration as...
dear nordic employee:
I want to use the PPK measure my hardware
I set as the 《PPK_User_Guide_v1.1》 says,and the led1 is ok
but the ppk cannot work well
the details like...
