I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
We are using nRF51822 in our custom board.
We just remain two pin ------ SCLK and SWDIO
Can we programming by STLink ?
what's the step?
1.using nrfgo studio to programming...
I tried setting the name as AT+NAME=LGS\r\n
When I send AT+NAME?\r\n, I do read back the new name, i.e. LGS.
However, the bluetooth host continues to see my device as...
Hello, I am using the sim card that comes with the Thingy91 in Sweden, it works well but every time I reflash the thingy with a new version of my application it takes several...
I went through each of the steps for upgrading the thingy91 modem firmware -> application firmware -> 52840 firmware but when I look at the lte link monitor it looks like...
Device: nRF52832, SD132v7.0.1, NRFSDK 16.0.0
Host: nRF52840 USB BLE dongle, pc-ble-driver-py 0.14.1, Python script, Linux
We're developing a device that's a BLE Peripheral...
Hi, I am looking for any suggestions on heart rate sensors i can use that would easily integrate with the nrf52832. I am looking to get a finalized output from the heart rate...
Hi I have a few questions about bluetooth 5.1 and the CTE packets that it transmits.
1. I know that there is a physical difference in the hardware of a Bluetooth 5.0 chip...
Hi,
I have nRF52840 dongle PCA10059. I want to use dongle as sniffer.
So how and what hex file and other thing i need to do ? To use dongle work as sniffer.
Hi,
I have been trying to get UART working properly on my custom board but also on nRF9160 DK. I'm using only UART_0.
With CONFIG_USE_AT_HOST and without any uart code...
tag v1.1.0 (have done west update) using SES 4.30c as suggested by nrf connect Compiled and flashed using SES modem firmware mfw_nrf9160_1.1.1 downloaded and updated the certificate...
I have developed a ble5 long range and meshing product but my life is way to short. using 2-3.6v batteries in parallel and only getting 2 months life in my battery calculations...
Hello everyone !!
While in test, I use Phone Mi Max 2 communicate with NRF52, sometime NRF52 send to Phone but Phone didn't received. I used sniffer and see packets to be...
Hi !
We are planning to add sensor device over Mesh network.
This sensor device will share Room Temperature, Outside Temperature, Humidity, ambient light and movement...
