Hello,
I have set nRF51822 Evaluation Kit. With its help, I would like to read the pulse of the heart rate monitor:
link text
I manage to connect to it using the...
Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hi,
I want to maximize the indication data throughput and minimize the latency with 4 connected devices.
Setup:
I’m using a nrf52840 as a ble client (sdk 15.2) that...
Hello, I updated the SDK and related SoftDevice of a project based on nRF52832_xxAA
from: 14.2.0 nRF5 SDK - 5.0.0 SoftDevice S132 (compiled works with #define NRF_SDH_DISPATCH_MODEL...
Hallo,
i am currently working on my thesis and i need to build a broadcasting network, in which each node must be able to trasmit to all other nodes, and at the same time...
I am working on project which is based on nrf9160 Development board.
Where the clock is initialized in example code of thread or GPIO ? Which clock source is used by nrf9160...
Hoping this is a simple fix. I'm new to using GIT and I'd like to setup my nRF 5 SDK projects to work with GIT so I can backup and collaborate with others. I have a few nRF...
Hello
I am interfacing between a SPI Master (microcontroller) with a SPI Slave (nRF52832 based chip) and I get the following output on both ends. The transmission seems...
Hi,
I have run into an issue with nrf52840 on pca10056 v1.0.0 board. The softdevice is SD v6.1.0. It seems to be a hardfault which cause a reset when I tried to call sd_flash_write...
Hello,
I need to read resistive sensors values with SAADC. These sensors going throught multiplexer and amplifier. Infortunaly, the signal going into the SAADC is noisy...
There is a race condition in the SAADC driver when using buffer convert.
I am trying to drive ADC at maximum rate to sample 3 ADC channels, and so I call the following in...
Hello,
after I could not use the nRF9160 DK I bought almost a year ago in Germany due to the missing nb-iot coverage I was very curious about the Thingy91 and I assumed...
Sorry for a noob questions but it is essential at this moment as I have not done any development on NordicSemi chips.
What software and hardware tools I need to develop...
Hi,
I am developing a PC SW that connects to nRF52840 device throw a BLE USB dongle(another nRF52840)
How I can tell from PC that a device is connected\disconnected...
Hi,
I use nRF9160 custom board and my application uses USART, ADC, I2c, SPI, RTC and LTE modem. Currently I am trying to reduce sleep current on IDLE state which is 850...
I am going to use nRF52833 chip with SDK v16.0.0 and SoftDevice s140.
There are couple of questions I would like to clarify:
1. Is AoA/AoD direction finding supported...
Hi
Using the nrf52840-dk with SD S140 and nrfx_gpiote, everything runs fund (BLE, TWI etc) but interrup on pin 0,28 causes a Hard Fault. I can not get any sensible logs...
