We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hey everyone!
How often does PM write into FDS? On each connection? Or on each new bonding? PM has some kind of peer ranking so I suppose that it needs to write on each...
Hi Nordic Forum! I'm currently developing a CLI controlled BLE scanner using the nRF52840 Dongle. Essentially I brought over the CLI example and adapted it to the a central...
Hi
it looks like the Publication Retransmit Count and Interval states default to 1 time and 100ms respectively. Is there a reason these defaults apply? I don't think it...
My thingy:91 does not connect to the LTE network. However it does detect the Swisscom network (Switzerland) and shows it as available. After a few minutes it sometimes changes...
I would like to program the 52840 with the HCI_UART sample to use it for Bluetooth scanning. I did this and lost the USB serial out. I now understand that on the Thingy91...
Hello,
I am evaluating the nRF52840-DK. I just want to play around with Nordic for awhile to determine if I want to port my current project which is written in C++ for Teensy...
I want to run various applications in some cases
what I want is :
In general, it runs own application.
When external memory(SD card, USB, EEPROM, etc... something...
Hello All,
I have developed advertising init in 14.2 sdk (in segger ide).
(working on nrf52810 board)
I wanted to migrate same functionality to 15.3 sdk so how i can...
Hi everyone! I am using the STM32L4xx Sensortile to transmit accelerometer data from the Sensortile Acceleromter. The characteristics of other functions are shown on the nRF...
Hello guys,
I wan`t to make an project that send trough serial port a new image to flash my nrf9160.
By the moment I managed to send and recieve data but only on uart0...
Hi,
Iam running the BLE uart and zigbee light multi protocol example. Using the latest thread and zigbee SDK v3.2.0. The example is quite good. That the door(zigbee+BLE...
Hello,
Where do I find the plating material information for the following part numbers? is it Matte Tin?
Nordic Semiconductor nRF51822-QFAB-T
Nordic Semiconductor...
I design a 4 layer pcb which include nrf52832. But i'm unsure what rf trace width should be on 4 layers pcb?
This trace 30mil width and 5mil clearance for 2 layers pcb as...
Hi,
I am using NRF52. i have custom board on that external flash and SD card is not available. i want to use msc class so that i can drag and drop file and read it in controller...
