Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I'm a newbie here.
I have a BL652-SA module from Liard Connectivity. It has a nrf52832 with a 32 MHz crystal on board but no 32,768 kHz crystal, so I have to use...
To the kind attention of Nordic support team,
I have been successfully using all gzll routines like in https://devzone.nordicsemi.com/f/nordic-q-a/57839/how-to-prove-to...
Hello-
I am developing my first project with the nRF9160. It is on a custom board. I am planning on using Segger studio with the Segger JLink programmer with the 10-Pin...
I am using nRF52832_xxaa DK and compiling ble_app_eddystone example. I am getting the following error
JLink info: ------------ DLL: V6.54c, compiled Nov 7 2019 17:01:02...
I wrote a simple application which updates a 16 bit characteristic as fast as possible (after initializing everything). Similar to the following:
The function called checks...
Hi,
example : nRF5_SDK_15.0.0_a53641a\examples\peripheral\twi_sensor
I am using the HTU21D sensor. I was download the twi_scanner example to scan the HTU21D sensor's slave...
I am having a problem talking to a MMA8653FC 3-axis Accelerometer from NXP.
I never see the clock signal generated.
I am using the nRF52 lib, communicating to a nRF5280...
I am converting the the Project ‘usbd_ble_uart_pca10056_s140’ to pca10059, to download it in the nrf52840 dongle. I followed the steps in the nRF52840 Dongle Programming Tutorial...
Hi,
I have some problems when I tried to compile pc-ble-drivers (C) .
1. When I tried to execute ./bootstrap-vcpkg.bat after I follow the steps:
$ git clone github.com...
I’m studying the NRF9160-DK board - I installed the Basis SIM card and followed the instructions : www.nordicsemi.com/.../GetStarted
I launched the Link Monitor program...
Hello,
My thingy:91 is publishing its messages to nrfcloud (=to the corresponding AWS mqttEndPoint and topics/ I suppose AWS IoT Core).
Now I want to get/process these...
In the example / serial in SES I see the softdevice is loaded as an "additional load file"
$(SDK_ROOT:../../../nRF5_SDK_16.0.0_98a08e2)/components/softdevice/s140/hex/s140_nrf52_7...
I am quite new to the nrf9160. Trying to run the gps example https://github.com/ExploratoryEngineering/nrf9160-gps . But everytime I get an error Failed to start GPS. I am...
Hello, the SDK example ble_peripheral\ble_app_uart includes the code below in order to forward data from the UART over the BLE. What it does is wait for a CRLF, or a certain...
