i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Hello,
I'm developing my custom sensor application. It's a matter over thread device. Before final product I'm working on a NRF52840 DK PCA 100056 v3.0.1 and NCS 3.02. It...
Hello,
I higly need to run twister unit tests in debug mode with breakpoints, step by step, spies and other debug tools in vscode. I did not find a way to do so.
Is...
Hello, this is probably a very beginner question but I don't know how to configure interrupt for the GPIO headers on the nRF52840 dev kit. I tried to search in this forum...
Device Overview
We have developed a smart wearable that sends notifications to our mobile application over BLE. Under normal conditions, the device alternates sensor...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
In the specification of 6.18.12.7 IQ sampling，The d escription of magnitude and phase .
I dont understand about magnitude e quals 1.646756*sqrt(I^2+Q^2) ,Why about 1.646756...
I am using the discovery manager to do device discovery on any device that connects to my central. I there a way to read the data in the characteristic during this discovery...
Dear Nordic
I am using nRF5 SDK 16.0.0_98a08e2 , and studying the example ble_central\ble_app_uart_c.
I found that in function
BLE_GAP_EVT_ADV_REPORT disappeared, while...
Hi,
I can't find any ses project files for PCA10031 (dongle) in nRF5 SDK V16.0 when examining the [.../examples/ble_peripheral/ble_app_hrs] folder. Additionally, there doesn...
Hi,
I've been skimming through the NRF9160 FOTA samples and related libraries(1.1 and master) and having hard time to understand some of the basics.
My assumptions...
HI,
I want to power the system using a external regulated 5V source. Then nRF5340 must be used in High Voltage Mode. When operating in High Voltage Mode, the nRF5340 is...
Hi Nordic Pros,
I have a nrf52840 board, and I tried to connect it to my pc. It dosen't show up as "JLink" or "BOOTLOADER".
Inside Segger Embedded Studio, I tried to connect...
Hi, anyone call tell What is the acceptance rate of nrf52 series scanning
I'm used zephyr ble mesh example, One node sends, one node accepts, and the broadcast packet sent...
Hello,
When i build a project to the nRF9160 DK, the terminal shows output of the program. Everything works.
When downloading the merged.hex file to thingy91, then...
Hello everyone,
We are 4 students, who are developing a BLE mesh network to send data from a CANNBUS-simulator to a desktop. We have chosen to use the nrf52840 chip to set...
Hello,
I am using nrf52832 with SDK 16, I want to change advertising packet flags from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE(0x05) to 0x04 during run time how can...
Hi, Im developing an ac dimmer with zero crossing on mesh, but it flickers at low dimming levels, I even used the scheduler for the ble stack but it didnt help, what would...
hi, i am using nrf 52840 dongle , is there any support of AT commands to communicate with dongle .i want to communicate without using ui only by sending commands. if not any...
Hey Nordic Team!
My requirement:-
Sensor data----------------------------->nrf52832------------------------------>Raspberry pi 3 (via blue tooth)
Is it possible...
