I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
im trying to turn on LEDs on my custom nRF52 board. Im using LEDs on 13,14,15 pins. I config pins in pca10040.h to my LED pins, but they dont work. Also if i try to...
I am trying to set up multiple ble diagnostic type services for different sensor devices, from a single nrf52840. The services share a common base id and some have the same...
hi! I'm trying to use the following to configure the GPIOs in nRF52DK for the LED blinky.
nrf_gpio_cfg_output(pin_number)
But I'm not sure what number should I use for...
Hi Nordics,
all the examples provided for searching for advertising peripherals use some sort of filter ( NAME, MAC, UUID, WHITELIST etc) . My questions is: Is it possible...
Hello Nordic Team
I m working in BLE project .
1)I want to get list of scanned devices .
2) I want to store the scanned devices in array .
3) I want to connect with...
Hi everybody
I use the nrf52 SDK (nrf5_SDK_15.2.0) to develop the IoT application of BLE. The IoT device acts as the TCP server and the BLE gateway acts as the TCP client...
Hello,
What is the least version should I buy to for nRF52732 software development.
Keil offers Essential and Professional versions, but the price doubles for Pro.
Our...
Currently I am developing application which run on nRF52832. In this application I have to decode and encode messages using RSA 2048-bit keys pair. Currently I am using ARM...
Hi,
I just want to know if this is an expected behaviour of the Softdevice. I have a central that scans every 2 seconds for 1.7 seconds (leaving 300ms for connections...
Hello,
I am thinking to use nRF52840 EVK for our project. I am supposed to use Katalon ( a tool for test automation) and Katalon works with Java. Hence, I will need a Java...
I have an existing setup, where firmware is transferred to a nRF52832 over a BLE USB dongle PCA10031 (V1.1.0) and nrfutil. This setup has been automated on our CI system/tools...
Hello,
I was able to compile my example codes successfully. All of sudden I have started seeing Error starting Process JAVA.
Has anyone faced this issue?
Can you please...
Hello Nordic team ,
I am working in BLE project ,while I am scanning device(filter) am getting (error 18) . Need your help team
Sd ble gap connect returns error code...
Hi.
I am trying to start development using Thingy:52. To start, I tried the firmware from the download page ( https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms...
The Limitations subsection of the Zigbee Section here contains the following paragraph:
- OTA DFU: Migration from the nRF5 SDK for Thread and Zigbee version earlier than...
