Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Currently I am developing application which run on nRF52832. In this application I have to decode and encode messages using RSA 2048-bit keys pair. Currently I am using ARM...
Hi,
I just want to know if this is an expected behaviour of the Softdevice. I have a central that scans every 2 seconds for 1.7 seconds (leaving 300ms for connections...
Hello,
I am thinking to use nRF52840 EVK for our project. I am supposed to use Katalon ( a tool for test automation) and Katalon works with Java. Hence, I will need a Java...
I have an existing setup, where firmware is transferred to a nRF52832 over a BLE USB dongle PCA10031 (V1.1.0) and nrfutil. This setup has been automated on our CI system/tools...
Hello,
I was able to compile my example codes successfully. All of sudden I have started seeing Error starting Process JAVA.
Has anyone faced this issue?
Can you please...
Hello Nordic team ,
I am working in BLE project ,while I am scanning device(filter) am getting (error 18) . Need your help team
Sd ble gap connect returns error code...
Hi.
I am trying to start development using Thingy:52. To start, I tried the firmware from the download page ( https://www.nordicsemi.com/Software-and-tools/Prototyping-platforms...
The Limitations subsection of the Zigbee Section here contains the following paragraph:
- OTA DFU: Migration from the nRF5 SDK for Thread and Zigbee version earlier than...
After installing nRFgo Studio v1.17.1 on Windows 7 64 Bit (using the administrator account), I get an error message in the Log section just when I start the program:
"JLinkARM...
I'm using SDK 14 and trying to build the ble_app_buttonless_dfu example. I'm using Linux environment, so gcc for building. When I try to build the example I'm getting an error...
Hi, I was just wondering why there is a "nrf_delay_ms(200);" in the SPI Master example in SDK 16.0.
Here is the code in the main function where it is located :
while ...
Hi Support,
Now I am developing over Nordic 52840 DK (PCA10056). My environment as below,
(1) upon SDK (nRF5_SDK_15.3.0_59ac345)
(2) softdevice s140_nrf52_6.1.1_softdevice...
Hello,
I am using the nRF SDK for Mesh v.3.1.0. To achieve periodic publishing, I set p_pubstate -> publish_period . step_num = 1 instead of zero in the configure step in...
Hi,
I plan to design my own hardware based around nRF9160. Prior to this, I want to verify that I can use the nRF9160DK as a debugger for my own board. As an initial test...
Hello,
We would like to develop a wireless sensor network using the 802.15.4 stack in nRF SDK.
I wanted to know if it is possible to port the existing 802.15.4 example...
