Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello Sir,
I would like to ask about the handling of the interruption in the nRF52 SDK.
The versions for SDK and SoftDevice are 15.3.0 and S132 v6.1.1
In the processing...
Hi all,
I am using a nRF52840 with SDK v16.0 on SES. I am trying to understand the flow of code in the secure Booloader(/SDK_v16\examples\dfu\secure_bootloader\pca10056_s140_ble...
Hi ,
I am trying to interface sg90 toy servo with NRF52840 , I am using nrf library but dont know how to drive it from 0 degree to 90 degree to 180 degree . May I know the...
Hi
I m using NRF52832 for beacon application.In my application, the device should be in the system off mode .After holding button for 5 secs, the system will back to idle...
Hi
I'm using SDK version15.2 and SD on a custom board based on nRF52840.
The board has two serial ports, and I want to use both independently. Using the Serial Port Library...
Hi Nordic Team,
My requirement is-
Advertise -> Connect to 1 device -> Send packet -> Disconnect -> Delay(1min) -> Advertise -> Connect to 2 device...
I am using Timer...
I am using nrfMeshProvision cocoapod to create a Mesh Network using a iOS Mobile application. In first step of identifying the device, i am able to call bearer.open() and...
Hi,
I've used the nRF connect 'Getting Started' software and tutorial to setup a development environment, however i am having problems with the "Set up a project in SEGGER...
Hi Nordic Team,
Please share a logic to filter with address for connection over BLE. Please help as soon as possible.
Thanks & Regards,
Aswati Vijaykumar
Hi
I am currently developing a demo application and started with the ble_app_template project from the ble_peripheral_folder (s140 softdevice, sdk 16.0). I copied it to...
I am using a module called Core51822 which includes NRF51822, with the NRF51822 Evaluation kit and the ST Link to program it from Arduino IDE.
I want basically to program...
can someone suggest me some tutorials how to do programming in nrf52840 from scratch.
i have tried some examples like blink an led just like opening the file and running...
Hallo devzone,
i have a real time task, where i have a trigger, different calculations and then the corresponding action.
Now i need to calculate the time from the trigger...
Hello,
As I am new to the world of bluetooth and its stack I have a question which I cannot find the answer for on the internet.
I've read a ton of posts on the devzone...
