Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi,
I'am using sdk14.2 with S140 V5.0.2-alpha.
I want to measure a time execution of a snippet code (ciphering function), and i want to display the time value with NRF_LOG_INFO...
Hi, Wizzards
I understand that the QSPI is made solely for external flash, but we are in a hurry to make a driver for a RGB LED module with a common clock. It would be good...
I have been using nRF Toolbox –DFU to reflash my project. I am using an Android tablet version 6.0.1. This process was working very nicely.
On 2/5/2020 the tablet updated...
Hi,
I have a really hard time with nRF connect. I wrote a simple app for my Dongle and when I want to program it via nRF connect it says that Device not found due to failure...
Hi,
We're trying to add a custom service to the HID keyboard example. the service is initialized we can see the service when connected to the device from the nrfConnect...
I tried original ble_app_hids_keyboard_pca10040_s112 example, then modify it by moving the code for typing h.e.l.l.o from Btn 1 to Btn3, and all possible combination of sd_ble_gap_disconnect...
I've tried using LESC without bonding, but iOS displays a pairing dialog. I don't think it is possible to avoid this, so the only way to avoid the pairing dialog is to use...
We are using nRF52832 to develop our product with the ANCS function.
But after bonding with the iPhone and then restart the iPhone, an error message "NRF_ERROR_BUSY" will...
Hi,
I've setup nRF Connect SDK v1.1.0 and I was taking a look at the the peipheral_uart example. I couldn't find any API reference when I searched in the v1.1.0 documentation...
Hello,
I sae that there is the possibility to upgrade the modem via FOTA/OTA application (for example asset_tracker), now without touching the modem could be possible to...
Hello,
Are there any hardware constraints or hard forks in putting an older version of an SDK, such as v11.0.0, on a much newer chip?
I'd like to port SDKv11.0.0 to...
Hello,
Is there any existing firmware where the nRF9160 can act as a coprocessor -- accepting AT commands and the ability to forward LTE data to and from a host application...
Hello, i am a beginner, i am parsing a dimming example. i have two client and server boards, as well as an nRF Mesh application. I can change the brightness of LED by pressing...
Dear Sirs,
I have dveloped application based on the ANT rx HRM example and with nrf52 SD board works perfectly (pca10040(
I would like to move to this application into...
I am using ble_app_gls s130 SDK_11. Is it possible to have pairing with static passkey without bonding? This is because the nRF device will be connected to different smartphones...
