hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hi Team,
I have a some query regarding nordic mesh
I would like to know that Nordic mesh is compatible with CSR mesh ?
Does nordic mesh is compatible with any 3rd...
Dear: Addressee
Hello!
I have a question about the program development of Bluetooth chip.
There is no client program for blood pressure measurement in SDK (15.2.0...
To do a serial DFU I have followed the steps provided in the DFUMaster_UART link.
1) Generated the key using the NrfUtil.
2) Added the private.key and generated a DFU...
Hi,
I try to flash application + softdevice + bootloader into the nrf52810 with following commands but it does not work? Can you look into this?
nrfjprog --program...
Hi,
We are developing central scanning mode for our project requirement. We want to scan BLE tags which are transmitting at every 10 seconds. I have been using nRF52833...
Hello, I have a working application that transmits data to a smartphone using NUS, based off of the uart example. I would now like to integrate bonding into my application...
I have an NRF52 DK and a J-Link mini debugger. I'm trying to connect J-Link debugger to the NRF52 via the debug jumper port. I'm using a standard 10 pin SWD JTAG cable. I...
i m working with fds using segger, i'm trying to perform read and write functions and printing on putty. it showing no errors on building while debuging no output is displaying...
When create 128byte length's CHARACTERISTIC and read with NRFCONNECT on Android. NRFCONNECT returns GATT_READ_NOT_PERMIT even though sd_ble_gatts_rw_authorize_reply() completes...
Hello Team Nordic,
I have a strange problem with the UART:
I am using nRF52840 with two UARTs: UART1 for Debug-Terminal and UART0 for communication with a GPS-Module...
I have developed a code for transferring data through uart to ble. It is working properly. but when I add a line printf to my code the data transmission stops and ble will...
Hello, I am trying to use the Legacy TWI Driver in SDK 15. I have setup my my sdk_config.h file to remove all references to NRFX (New TWI Driver). Only enabling the "nrf_drv_twi...
Hi!
I have download nRF5_SDK_14.1.0, and I have IAR Embedded Workbench IDE ARM 8.20.1
I want compile ble_app_eddystone.eww from examples, but have error:
Error[Lt009...
I'm looking into the use of the nRF52840 as a light switch/dimmer for a Philips Hue system, but have been running into issues with getting connected to the Hue network. I...
I know there have been many posts on this forum regarding a similar issue, I have spent a whole day reading them and trying to get this working, to no avail.
Basically my...
