We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello, Is it possible to do a save as or copy an example to another directory/folder without having to re-link all the .c files? I am using SES 4.30c. Every time I take an...
I am developing based on 52840. I can only supply VDD at 2V. I wonder if that is doable. If the answer is yes, then how should the VDDH be connected?
The datasheet requires...
I have custom board with nrf 52832. I am using SDK 15.2.0 and softdevice s132 V6.1.0 to transmit advertising packets periodically. I have written simple application that reads...
We use nRF52840 chipset to design a BT module, and it went into pre-production now. But we found the RX sensitivity is not good. We need your help to confirm the RX sensitivity...
So I am using nRF52811 and I have noticed the battery voltage going at a constant rate and suddenly for a time of 2 mins the Voltage value (ADC) dips and it comes back to...
Hi,
I read many post on devzone, but still not familiar with programming "custom board" in my case, board from Sparkfun. My Sparkfun is correctly connected to nRF52832 DK...
Hello,
I am working to replace my BM70 with nRF52 series. So it has to be quick and simple solution. So, I used nRF52840 USB dongle as my slave (Peripheral Example code...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Is there a way to know the cause of the reset?
I connect the PC to the device and run it in debug mode. However, nothing is written...
I'm running SDK 15.3 with SD 132 and SES 4.30.
I am working with the ble_app_uart_c as the base code and adding other functions. I've gone through the app_timer tutorial...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - Chip) and Nordic SDK v.14.2.0. Now I try the SPI example and I don't know which register is adressed in the last...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image.
This issue is similar to below ticket with -eraseall and chiperase...
Hello,
Im configuring ADC on 3 channels. However during debugging when I stop Keil I see that in all channels the acquisition pin is the same AIN1.
Any idea why is this...
Hello, I found an examples using ble_app_uart and and MPU6050 from different SDK's. I am trying to update the to SDK16 and have got it to build successfully but when I try...
