Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I'm using NRF52840, and I've developed a feature which bonds with NRF toolbox application. The problem is that when I'm using secured BLE, I can't receive any messages...
Hi,
I have an issue with getting a GPS fix from time to time under the almost same conditions. When it did not get a fix I could see in the UART log that the nRF9160 was...
Our custom board has an nRF52832. In our custom build system the application HEX and SoftDevice HEX are merged together into a single HEX file, this is achieved by Nordic...
We are in the process of getting our product through SRRC certification in China. I am using the radio_test example from SDK 11.0 for this. All is working fine.
However...
I downloaded SDK v16.0 and in the examples, I can't seem to find the dual_bank_ant_s332 folder.
It is present in SDK v14.2.0 in this path
...\nRF5_SDK_14.2.0_17b948a\examples...
From what I can see so far, it appears that the application processor flash is at 0x00000000 - 0x00100000 and the network processor resides at 0x01000000 - 0x01040000 .
...
I am having trouble because TX / RX processing using UARTE cannot be performed.
nrf52840 DK <---------> PC
The operation of TX / RX can be confirmed with UART. (Interrupts...
Hi,
I have two questions:
1) After requesting PSM mode (assuming the MNO supports PSM mode for NB-IoT) and afterwards enabling GPS, does the GPS automatically detects...
Hi,
I am currently working on the development of a customized Tracker application. I was testing one use case where the Tracker definitely not being able to achieve a GPS...
Hello,
I'm using BT840XE module and ATT_MTU Throughput Example with S140. My goal is to measure maximum data transfer speed between module and different phones. Module acts...
Hi,
I'm using nrf52832 (SDK 15.3). And I have 24 chips on the same I2C bus. They all work fine right row. But if one of the chip is broken, the whole system will crash....
If a reliable mesh transfer is ongoing the node will crash with a mesh assert at access_reliable.c:373, in access_reliable_cancel_all().
This happens because access_clear...
Hi all,
I am looking for the Objective Product Specification for the nRF52840 chip. I have only found the Objective P roduct Specification for nRF52832 in version 0.6.3...
After setting up my Peripheral Mode I am also looking at ways to improve my current design. I would like to ask about Mesh support on the NRF Thingy 91 integrated with the...
Was anybody able to connect to HTS (Health Thermometer Service) on iOS applications, OTHER than nRFToolbox or LightBlue? Which applications did you use?
I tried a dozen...
