I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Hi. We are using the USB CDC example to send data to a windows PC over virtual comport.
First question is that in the sdk_config.h file NRFX_UART_DEFAULT_CONFIG_BAUDRATE...
Hi Nordic Team,
Please suggest logic to scan all peripheral devices by the central device.
In my BLE project when I'm trying to scan all peripheral devices which are advertising...
Hi Nordic Team,
In a BLE project we need to configure same device to conditionally act as central (to scan) device and peripheral(to advertise) device based on the state...
If I write to the MWU REGIONENCLR register and immediately access memory that was previously watch enabled an event is still generated. If I delay a small amount (tested with...
Hello,
we have made our fist device with a custom Service with 5 characteristics. And now we have a strange problem which I was not able to debug to find a solution.
We...
Hello,
if I call this code all works:
if I call following code only ZB_ZCL_ON_OFF_SEND_ON_REQ take effect on target
I'm simply swap the call order, where's the error...
Good morning everyone,
I saw this question asked a few times, but no conversation was actually fixing the issue.
I am developing a product where I want the pairing to...
This seems to have changed in recent SDKs, so that none of the examples or techniques mentioned in previous posts is relevant any more.
I am using the SDK v16.0.0 ble_app_blinky_c_pca10040_s132...
When I carefully follow the instructions at https://infocenter.nordicsemi.com/topic/sdk_tz_v4.0.0/thread_ot_libraries_building.html , I am missing some of the openthread libraries...
Hello.
I just started using nRF52840-DK board with SEGGER Embedded Studio and I'm trying to use it to save data in a micro SD through an adapter. I tested it with the Fatfs...
SDK15, nRF52832, S132
I notice that after about 30-50 bond and delete cycles peripherial to central, central doesn't want to bond. Before it bond and after that delete bond...
Hi there, I am working on controlling the nRF Mesh device (nRF52840-DK) via the bluez version of 5.52 (meshctl). I try to connect to Nordic nRF52840-DK (example <nrf5_SDK_for_Mesh_3...
Good morning,
Is it always required to use Segger J-Link in order to flash Bootloader, Softdevice and Application to a new device?
Could you summarize the different possibilities...
I have an application where I will require an external antenna as our product sits in a metal enclosure.
The example NRF91 DK development board shows a UFL connector (which...
