Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I was doing some stress testing of TCP connections and saw an oddity go by that has me scratching my head.
Here's the order of events as best as I can figure from correlating...
Hi,
I already achieved the update of all available nodes in a mesh network, where the update is injected over a serial connection to one node.
Now my question is, if I...
Hi
I'm confused by the concept of switching slots and sampling slots, or at least the way they are presented as being interleaved. For BLE, I believe that they are required...
I am considering using a high-Q BAW filter to drive as near the band edges as possible and roll-off noise beyond.
Source of my interest:
https://www.qorvo.com/design-hub...
I am using nrf52832 SDK14.2 development, now the system will generate some strange exceptions, I am worried about the stack overflow, is there any way to confirm whether the...
Hi All
We are using nRF9160DK and want to send data to the cloud (Adafruit or Thingspeak) using MQTT protocol but we do not have NB-IoT
Network in Our area so it's possible...
To the kind attention of Nordic support team,
I've been reading in this post:
https://devzone.nordicsemi.com/f/nordic-q-a/44042/using-nrf52810-with-gzll_nrf52_arm-lib...
Hello,
I need to validate my selection for crystals working with the NRF52840. For the 32.765kHz crystal I have chosen the 9HT12-32.768KBZC-T from TXC Corporation. For the...
i have test with RTC using nrf_calender.c.
It will prints output data on terminal window.
But, I didn't recognize the actual data.
Output data is mentioned below,
...
I am attempting to use libmbedcrypto.a from the Thread/Zigbee SDK version 3.2.0. I am linking it from:
external/openthread/lib/nrf52840/gcc/libmbedcrypto.a
and yet...
HI,
I want to implement the software security to NRF52832 such a that no one should be able to read the memory or tap the data during Bluetooth communication.
Regards...
Hi,
I am trying to interface tlv493d with nrf52 dev board.
I have taken driver code from infeneon
https://www.infineon.com/cms/en/product/evaluation-boards/tlv493d-a1b6...
Hi
I face ble disconnection issue.
we use external crystal 32.768khz. However, when I check it , the load cap is wrong. It should be about 9pF but it is 1pf.
The frequency...
Hi,
When factory resetting the flash storage, I delete all records, and then call fds_gc(). However, the page that's used for garbage collection still contains a copy of...
