The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I have been working to get the secure_bootloader examples to run on the NRF52832_XXAB (QFAB with 32kB RAM and 256kB Flash).
Apart from the fact that I had to change the...
Hi,
Good day!
Problem statement:
TSM12 Capacitive touch sensor IC (I2C com supported) is used in our application. It has got 12 output channels and Channel 1 is a parallel...
I am trying to send a string from the board through uart to the PC(windows) through usb-ttl. I tried using adruino and was able to successfully execute it. but when i tried...
Hi,
I've used the 'Getting Started with nRF9160 DK' tutorial to setup a development environment, I have a problems with loading asset_tracker project. My output:
Loading...
I understand there is a hard fault happening in the SDK. I am using SDK 15.3.0, I am not on a sdk example, but on a specific program I am doing I can't share. It happens a...
Hi,
I added a small shunt resistance to see current consumption of nRF52832.
I see current ripples when DCDC regulator is enabled, this ripples doesn't exist when DCDC...
1. We are running our nrf52832 based project on Eclipse and are able to compile, build and run the project on our target hardware. So far, so good.
2. Now, in addition we...
I'm working with the light switch server example and nRFMeshProvision example project for iOS.
How do you send arbitrary data to a board? I understand the provisioning process...
Hi,
I noticed that there are a few methods in nRF52 SDK v16 to blink LEDs:
Use bsp indication methods which seems based on app_timer;
Use led_softblink library which...
nrf52832, SDK 15.3
The average current consumption is 9.53uA in my system with SPIM. After I init another SPIS, the current consumption goes up to 478uA. CS pin keeps high...
Now I am using nrf9160DK for development. In my project, I need to use a random number generator and a highly accurate system time stamp. Is there an API that I can call directly...
Hello,
On nordic nRF9160dk I want to send SMS and receive the data from UART simultaneously. UART needs 3V VDD supply and for Sim card it is 1.8V. So how this condition...
Does SoftDevice S112 or S113 offer mesh support on a nRF52811?
The intended use is for an end-device running very simple app-logic. According to the SoftDevice properties...
Hi there,
I'm using nRF52840 dev kit board and v15.2 SDK.
I've set up a PWM using the PWM driver and is working well.
I'm frequently stopping and starting the PWM...
Hello everyone,
I have a nrf52832 (SDK v15.2.0) that is connected to a tablet via BLE. However, if I have several SPI transfers one after another, the BLE suddenly disconnects...
