Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello everyone,
I just started working with 802.15.4 using nRF52840. I wanted to know weather we can do RX-to-TX using 802.15.4. If yes what are the API's available to do...
We have problems with the restart which the application does after receiving the DFU attribute is written.
Startup should work like this as I understand it: the reset vector...
I have 2 hardware revisions, one with the GPS LNA attached to MAGPIO0, the other revision, the LNA is on COEX0.
In my prj.conf file, I have the following setup for handling...
From this guide:
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader#h61sjziauupw1j397q9s9ldr01q4j6d5
Appendix...
Hi,
I have the BC480 eval board and I would like to be able to upload the simplist application to it OTA. blinky_pca10056.hex
I'm using the Nordic Toolbox application...
'NRFX_SPIM0_INST_IDX' undeclared here (not in a function); did you mean 'NRFX_SPIM_INSTANCE'? error occured .
I am not using SPI , this error is not cured by me .I enable...
Hi
So I'm trying to adapt the ble_lte_gateway example at my nRF9160 DK but because I don't have a Thingy52 I have to use an nRF52840 device, so I wanted to try the sample...
I am working on a wearable design that has standalone modules distributed around the body. Each module will do the same thing, receiving commands to turn LEDs on/off or adjust...
Hi,
I am trying to us one more SWI with nrf_drv_swi_alloc , but returns NO_MEM => means there is not any free.
I looked to source code, and I find SD_SWI_USED is defined...
Hi,
I've added NUS service to my app (nRF52832, peripheral, FreeRTOS based, SDK 15.2, SD132). everything works great with MTU size = 23 bytes.
Now I try to increase...
Hi there,
I found very interesting behavior on casting double variables to integer.
The following code gives me strange result:
double dval = 0.;
int ival = (int...
Hey,
Currently I have been working on a project in which I have to calibrate the range of the bluetooth, basically I need very short range of about a meter.
Could anyone...
Hi,
I have some trouble using TWI : the slave device connected to nrf52 sends an ack signal (seen on scope) but the i2c handler raises an incorrect address error and discards...
