I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
I want my application to cooperate with DFU. I am using example DFU project from SDK (6.1) (from nrf6310 folder, i simplified it so it could work on PCA10000), but i need...
I increased my IRAM1 size as advised here , but now my program doesn't work anymore on the nRF51 DK.
I know the problem is somewhere in the memory allocation, because when...
I am working with nrf51422 chips version 2, so according to this table taken from the compatibility matrix v2.0, the last supported versions of SDK/SD/SDS I should refer to...
Also it seems not to advertise. What may cause this problem?
All I could found in the ble_gap.h is:
If both conn_sup_timeout and
max_conn_interval are specified...
Hi
I am trying to debug the "ble_app_hrs" example from SDK 6.1.0 (using keil IDE), on 51822 chip.
The IROM1 is defined to start at 0x16000 (meant to be used with softdevice...
I'm trying to minimize current consumption on my BLE peripheral and I wanted to know what advertising data is required. I have a custom service with a 128-bit UUID but do...
Hello!
I am using a keyboard (4x3) and the rows are configured as input PD and columns as output set, after a successful interrupt , the columns and the rows shift settings...
I am using nRF8001 bluetooth ble for my project. I would like to get the RSSI value as a reference value in my firmware. Is there any way that I can get the RSSI value from...
Hello,
I'm using the following (nRF51822-Beacon): www.nordicsemi.com/.../nRF51822-Bluetooth-Smart-Beacon-Kit
I would like to use the beacon for beacon-to-becaon and...
I am calling the spi_master_send_recv in a ISR from a GPIO using app_gpiote.c It causes a hardfault on APP_ERROR_CHECK(sd_nvic_DisableIRQ(p_spi_instance->irq_type)); Otherswise...
Hi,
The nRF Toolbox app on iOS crashes when opening user added files in the DFU. These files are added to the app via iTunes. The version of the nRF Toolbox is 1.7 which...
Hi,
We're producing a custom board based on the nrf51822 and would like to add a USB Serial chip.
The current contenders are:
a) FTDI 232R
b) ATmega8U2 ( www.arduino...
As the picture shows, I saw this softdevice_hex option available.
The error says, "require nRF_SoftDevice S310_Hex".
But where to this missing component.
My development...
Im sending an 8 bit int using my AVR controller as follows:
static uint8_t* dummy_heart_rate = 6;
aci_loop();
if (lib_aci_is_pipe_available(&aci_state, PIPE_UART_OVER_BTLE_UART_TX_TX...
