Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
I'm looking at designing my own Bluetooth Receiver essentially. Playing music from my phone to a Bluetooth receiver, to output via AUX.
I was looking at the range of MCU...
Hi,
For my all DFU i follow the steps on the Getting started guide , just in the Performing DFU step i use the nrfutil tool for the over USB.
First i tried with the DFU...
Hi team,
Similar to how we have recommendations to use certain pins for low drive, low frequency on the nRF52 series, do we have those recommendations available for the...
nRF connect is not recognizing my nRF9160 board when I try to use the programmer tool. It allow me to select it from 'select device' drop down menu. But then I select it all...
Hi,
I am working with NRF52832 boards where on one board i have loaded Multilink central example, and on the other i have loaded peripheral code with some modifications...
I have merged Light and DFU examples(Light_DFU), and test DFU update both blinky and Light_DFU.
It is always getting ERROR_BUSY (134) while update Light_DFU, but success...
Hi, do you have a schematic / diagram that shows the architecture of the asset tracker application / nRF Cloud?
Does it use MQTT for communication?
Does it use the AWS...
Hi there. I'm developing an NRF52840 project from scratch and wanted to obtain a "good reference" sdkconfig.h . I tried picking one from the examples (the UART example, 'cos...
Hello guys I am using nrf52832 dongle for development and my client has nrf52832 DK at the moment. I have completed my firmware that get ADC values and store data on SD card...
So, we have a problem that the new Samsung S20+ phone is not able to connect to the nRF52833 if extended advertising is enabled (using nRF Connect for Mobile app).
The phone...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am using app_timer to control the LED On time.
the app_timer...
Hi,
I am using nrf sniffer. I have used both nrf51422 and nrf52832. Here I am facing such kind of issue like. Once I am saving my report in wireshark and starting sniffing...
Dear all,
I'm using nRF52810, I want to achieve low power consumption(<200uA). I have disabled easyDMA. Right now I want to know how to turn on/off uart anytime we wish...