Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
Hi,
I'm using nRF Connect version 2.9.1 with the buildprog script method of building this project.
I've got some custom boards based on the nRF5340_audio_dk. We swapped...
Hello,
I've seen multiple posts related to this question, but they're not very recent so I wanted to check if there's an updated answer.
Are non-simultaneous multi-image...
I have an Ubuntu Machine where I successfully installed Zephyr SDK and toolchain following instructions given in the official getting started guide here . I was able to compile...
Hello,
I have a custom PCB with the nRF5340 chip. I’m able to flash the board using a J-Link. I’d like to rename the device so that it advertises a specific Bluetooth name...
Hi,
I am completely new to this technology,I need to interface BME 680[humidity,pressure,gas,temp sensor] with Nordic nRF52840 - how it is possible,i want know the hardware...
Hi,
I am using nRF52832 DK, with Segger Embedded Studio as IDE. I am using ble_app_uart example. I have used an encryption algorithm. The encryption algorithm is called...
Hi,
Does the SPIS generate interrupt for every byte of data receive ?
What kind of interrupt of event that SPIS will generate for data received ?
Please advise
Hi,
I need to assign Rising edge and Falling edge event in a single pin.
I try to assign both Rising Edge and Falling Edge event into APP_EVENT_PIN.
There is a error...
Dear all,
I have noticed that NRF_LOG_FLUSH() function is used in many examples after each nrf_log print function. In some cases though, the program freezes when I try my...
HI!
nRF52832, SDK13
I need to know what happen with setted output RF power when peripherial devie connect to central device.
For example, if output RF power setted to...
Hi,
I am completely new to this technology. I am currently programming a custom board equipped with an nRF52832 based on the ble_app_uart example in the SDK 15.2 and is...
Hi!
24 days have passed since I was promised an update (which I hope will mean a solution), but nothing...
Also, there is no updated Getting Started Assistant and the...
Hi,
We are planning to use an Automotive Grade Bluetooth SoC in one of our new designs.
Some controllers in the nRF51 family seems to be Automotive Grade, but we also...
I tested with Light Switch Example in nrf5_SDK_for_Mesh_v3 version, I have set Transittion time to 160 second and Delay to 0, problem occur is the device Cann't countdown...
Hi,
I am using an nrf52840 MCU, Nordic SDK 16.0.0 and IAR Workbench for ARM v8.40.1.
The MCU has the following configuration:
- MBR installed
- DFU secure bootloader...
Hello everyone,
I faced with bus fault after running beacon example from mesh_sdk. It occurred after calling mesh_provisionee_prov_start().
Unfortunately, I didn't found...
Greetings...
Provisioning w/ Android tool only works when board is connected to debugger.
Provisioning failed to even find the devices when scanning after disconnected...
When enabling 3 instances of SPIM (1,2,3) on NRF52840 the application doesn't start at all.
Weirdly however, the application works fine when SPI3 takes SPIM3 and the rest...
