Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
In my application after some timeout i am trying to stop BLE advertisement.
for this i am checking current connection state,If it is connected or disconnected.
if...
I'm using the TWI_MNGR to schedule a transfer. I have copied the nrf_twi_mngr_perform() function to a function called nrf_twi_mngr_schedule() which does everything except...
Hi team,
I am working with the nRF5340 PDK v0.8.0 and I am trying to request the additional voltage for the VREGRADIO to support the additional 3 dB TX power on the RADIO...
i have a project with Nrf24, i'm using NRF24L01 + PA LNA 2.4Ghz with athena, to get 1000m -2000m range.
But i saw on nordic website that nrf24 not for new design, we have...
I have seen a few references to SoftDevice in the 6.x series not being able to transmit at 500kbps in these forums, but I can't find anything in the docs to reference. Can...
Hi, I am using nrf52832 dev-kit. I use P0.23 or P0.24 as an input pin. I am trying use this pin to read data from other device. When I use this pin like button, it can detect...
Hello,
I would like to get some input on general framework options for development.
I am starting by strictly following the SDK framework, trying to use its drivers, translations...
Hi,
Sorry for putting so many questions in to single thread :)
----
I am looking for information on what all images been integrated to zephyr/merged.hex, can you point...
Hello!
I'm currently implementing Modbus RTU into my nRF52832 to enable the CPU to communicate with other Modbus RTU capable devices.
When communicating via Modbus...
Hi, I am relatively new with ble and nordic development. I am working with the nus service for communicating but now i also want to have ota firmware update. I am trying to...
When running the light_switch provisioner example, the application fails to the error handler when calling app_default_models_bind_setup, in access_model_application_bind...
Hi,
we are developing a device with 2 µC one being the nRF52832 for BLE connectivity. We want to do DFU via BLE with our own protocol. From what I've read, in this case...
For a customer I am developing a Zigbee coordinator / Gateway with the nRF52840. As hardware I am using the nRF52840 Preview Development Kit. As software basis I use the ...
Hello, a couple of get-me-pointed-in-the-right-direction questions, if you don't mind.
I plan on creating a system with an accelerometer that talks SPI to my Nordic nRF52833...
Hi!
I read that your Thread stack uses a different 802.15.4 implementation than the MAC driver. Is it possible to intercept special broadcast data packets e.g. from energy...
