Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Dear Team, I'm preparing an application for nRF52840 that will require to send and receive data collected from two different sources, I2S and UART, two UART or SPI and UART...
Hi Nordic,
Please provide the way to debug not able to write 14 Bytes data into Queued Writes module, my application not get any nrf_ble_qwr_on_ble_evt.
[Project Informaiton...
I am a little bit confused on the steps I need to follow to program the settings and the bootloader files. According to Secure DFU over Serial example instructions ( https...
Hello,
I am trying to download the program to my target using J-LInk. Unfortunately, I get this message (see bellow) and I don't know how to proceed.
Any help is appreciated...
Hi,
I am working on a project that utilizes mesh technology. I'm currently using nrf52832 with NRF Mesh 4.0
There are multiple devices that can act as a server and a...
Hi Folks,
Need some advice. We are sourcing voltage to a variable resistor from an output pin. We've configured this as a high ouput. The overall resistance of the POT...
Hi,
I'm testing ads1292 sensor with nrf52832.
I got some problem when i use spi manager library.
I'm using ble_app_hrs project.
If i use spi manager without advertising...
Hi,
We build a new board based on nRF52833 wlcsp,
I tried to run a simple code with BLE peripheral (ble_app_uart example), and I noticed that the HFCLK is not working...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Hi
I am running this example from SDK 15.2.0.
I am trying to figure out how the server knows at the end of the session how many bytes of data the Peer received.
Anyone...
The information on the website currently only supports nrf52840.
Can nrf52833 support DFU over USB?
If yes.Which example can be used? Does it use the same DFU USB bootloader...
Hello, I am studying the peripheral/ble_app_uart and peripheral/ble_app/template examples to understand the proper way to build a peripheral with our own set of services and...
Hi,
I have hard time to setup west in my Ubuntu PC. It was installed, but not fully working. So I tried to uninstall and reinstall, and also one time, I may have upgraded...
Hi All,
I have downloaded nrf5_SDK_for_Mesh_v2.2.0_src and trying to build the LIGHT SWITCH example but when i try to compile iam getting lot errors attached the screen...
