Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I have a little program that is built on top of the USB CDC ACM example. This little program waits for an SPI event, when the event arrives, it reads the SPI peripheral...
Hi,
For my project I use a ble central and a ble peripheral.
I have to send data from the peripheral to the central and i use hvx indication to do that.
I have two charactics...
Hi,
I am working on the asset_tracker application.
I have integrated the "lte_ble_gateway" into the asset_tracker application and able to get the BLE values from nRF52840_PCA20035...
I am trying to use PPI to control an output pin. I am successfully using 2 PPI channels at the moment to use the COMP to do freq counting over a 10mS time period. I have added...
We have our first prototype ready and were measuring the power consumption. During development the values seems to be wrong.
So I just added a voltmeter to the DUT out clamps...
I'm having the issue of where calling app_usbd_cdc_acm_write() more than once within the ble_nus_data_handler fails.
A test case is based on the "examples/peripheral/usbd_ble_uart...
Hi,
I'm looking at the recent SDKs for S140 and I can't see an option to enable the TxPower field in the extended advertisement indication packet:
I've taken a look...
Hello there!
So far we were using v1.1.0 branch of nRF Connect SDK. However, we would like to experiment with the AWS IoT library so we were forced to move to the latest...
I am trying to use nrf51822 as central device and connect it to another nrf51822 acting as a peripheral device ..and i want the central to print the rssi value with respect...
Hi
I'm working on nRF52832 with SDK 15.2.0.
I have a device which is based on ble_app_hrs_rscs_relay.
I added pm_handler_secure_on_connection in ble_evt_handler and...
I have downloaded the example application code from github ( https://github.com/NordicSemiconductor/IOS-Nordic-Thingy ) and am trying to build it using the latest xcode development...
Hello, Guys. Using the function ble_nus_string_send, I've sent sensor values to my mobile phone. However, the data received came from an unknown character being broken. I...
Hello,
I use aws_fota as starting point on a mobile device with MQTT reporting.
What is the best way to manage loss of connection (how to know and how to cleanly rebuild...
Hello Nordic support
We want to add a function to monitor the RSSI of the other party's mobile phone at the time of Connetion instead of advertising. Is it possible...
Hello Nordic Support,
I have modified the USB MSC example to use SD card and have also initialized UART port. Basically, what I'm trying to achieve is to write data received...
