Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I am currently working with the channel_sounding/connected_cs sample for nrf54l15 and I keep getting the error: Not enough memory to store step data (530 > 512). I tried...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
Hello, I am trying to use the subghz template in ncs 2.5.2 but I am running into an issue when enabling NanoPB. When enabling NanoPB with CONFIG_NANOPB=y the application faults...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
Hi Support,
I'm working on a project where I need to copy the contents of the internal flash from slot_0 to an external NOR flash partition. However, I'm currently unable...
Hi,
I am trying to install NCS v3.0.1 on Ubuntu 24.04 PC and I get the following error.
Looks like ZEPHYR_BASE is not setup. I am trying to follow the Fundamentals Course...
Hi
Can someone help out?
Why is there an empty PDU after every notification(length shown in trace with 277, my payload is 244). Are all packets with the same EVENT COUNT...
I am trying to integrate nRF7002 into my application firmware, by using the "wifi/sta" example in NCS3.0.1.
My application has CONFIG_NRF_SECURITY=y and PSA enabled and...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello, I need help understanding how MCUBOOT produces signed_by_b0_app.hex file from app.hex on the network core of nrf5340. My goal is to have a DFU updatable hex file (net_core_app_moved_test_update...
I am using nRF9160 to develop a product for a client that requires displaying the name of the current carrier on the screen. According to the AT instruction manual of the...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
