Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Dear Nordic Community We are about to develop a Testing-Framwork to compare different Mesh-Networks (Bluetooth Mesh vs. Thread vs. Zigbee) for which we would like to use the...
I've looked around on the forum and I can only find old posts about this.
Based on your repositories it seems like you support just about every big language except for Java...
Hi
I have a simple question which I am not able to figure out.
How do I use the nRF52833 DK without having it plugged to the computer. I tried switching the power to...
We are using a flash part that is 64 MB in size. It is S25FS512. We are trying to use 32 bit addressing mode by setting sdk config flags. However this does not seem to work...
Hi,
Greetings!
I just tried Low Power Node example application from SDK for mesh 16.0.0
It works functionally well, however I am little curious to know below point(s...
Hi,
I start developing with a new MacBook Pro (2019) which only offers USB-C ports. Currently I am facing the issue that the Programmer App does show the connected Thingy...
Hi!
I have recently setup the development environment for my Thingy 91 on Windows 10 environment using nRF Connect Getting Started Assistant. But I am having some trouble...
Hi, I am working on nRF Thingy52 for a week. I am having SES with SDK_16.
I am having 3 nRF thingy to do a testing purpose
First i need to analysis how the thingy works...
I'm testing using the internal RC circuit to drive ble via the S132 softdevice. Set up is with Nrf52DK and Power Profiler kit. I got everything running and was measuring about...
Hi, How can I configure the LwM2M server (URL, Port, Credentials) on my Thingy91? Can I do this via MQTT and the nrf Cloud or do I need some specific tools?
I have a GT832C.01 (Bluetooth 4.0 BLE sensor detection module BMX055 9DOF NRF52832), I don't know how to program it, I can see it from the phone, but what software do I need...
I have a BLE board with a nRF52832 and some peripherals. It came with a preinstalled bootloader and firmware (the bootloader supports DFU via BLE to upgrade the bootloader...
Hi,
I am completely new to this technology,I need to interface BME 680[humidity,pressure,gas,temp sensor] with Nordic nRF52840 - how it is possible,i want know the hardware...
Hi,
I am using nRF52832 DK, with Segger Embedded Studio as IDE. I am using ble_app_uart example. I have used an encryption algorithm. The encryption algorithm is called...
