Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
The bluetooth of android APP is easy to disconnect (we make smart door lock products); The product is delivered to the customer. It is easy to disconnect and not connect with...
Hello,
I learnt about some resource pre-allocation in the datasheet, e.g. ppi, or API documentation, e.g. app_timer rtc1. I see the SDK drivers are trying to take care some...
SDK16, S112, 52810. I have DCDC set up and external 32.768 crystal oscillator on my board.
Here is my code part:
main()
nrf_power_dcdcen_set(true); nrf_delay_ms(100...
Dear ,
Follow the previous ticket, https://devzone.nordicsemi.com/f/nordic-q-a/59034/agps_thingy91
I am trying to use asset_tracker : https://github.com/NordicPlayground...
I am writing an application on a BLE chip that will transmit high volumes of data to an Android phone (520,000 bytes / second signal).
According to some tests I've seen...
my board uses 51822. I am using 52DK to debug it. I have plugged my board with 52DK as following:
RX -> p0.08
TX -> p0.06
My question is, when I init UART in code...
Device: nrf9160 (dk and custom board)
sample application : MQTT simple
segger studio (nordic version): V4.42a
There are 2 main issues:
1) in the main.c file, Segger...
Last time I used it, it worked fine, it's been sitting in a drawer for some time since then.
When I tried to use it now, i get this error - even though I can read the...
Hi team Nordic,
Looking in the nrf53 datasheet, it seems like the PDM clocks are the same (peripheral) as the nrf52, is this correct?
You usually wanna run the newer high...
Hello,
I am using an nRF52840 on a custom board, and I want to add the workaround for Errata [87] Unexpected wake from System ON Idle when using FPU . However, the the...
Hi,
I´m trying to flash a custom board with nrf52833 chip with the nrf82833 DK.
How can i make sure, that tha DK board will program the custom board? Currently it...
Why isn't this working?
The MPU_RESET_PIN is set to : NRF_GPIO_PIN_MAP( 0 , 20 )
I can not seem to be able to alter the state of the PIN. Whenever I read the PIN its...
Hello all!
I have a timer that sometimes gets started inside the IRQ of the ESB and sometimes needs to be restarted inside its own IRQ
I'm running it in a "one shot...
Hello
This parameter must be modified e.g. if you have a large number of characteristic in your custom service.
is there a reasoning to calculate this or just "try and...
