In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
When working with a custom board with nRF52840 chip, I'm having serious problems with SWD connectivity. In many cases JLinkExe can't connect to target at all. I did some measurements...
Hi there!
I'm trying to simulate a peripheral with a PCA10040 and nRF Connect for Desktop.
I've made the Server Setup, applied to the board and started advertising - everything...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Initially I was in assumption that once...
Hi,
Is there a table / .xls available for ALL nordic parts to date?
I'm trying to find all options with +8 dBm TX Power & WLCSP package. (no need for usb)
Hi, I'm trying to get the nrf_stack_guard and nrf_mpu libraries to catch writes past the end of the stack. My stack is 8kB in size (0x2000E000-0x20010000). This is the log...
Hi,
I'm working on the custom board using nrf52832 chip and have performed the secure bootloader using ble on the custom board.
I have made these changes so far on the...
We want to connect provisioned node to multiple mobile application over same mash network (Note: We are trying to give access to multiple user(using multiple mobile) to connect...
Hello!
This may be the wrong place to ask, but I am in search of a gateway (off the shelf or a reference design), that incorporates 802.15.4 through the nrf52840, cellular...
Hi,
I just have a small question: say I have two models, both with publish timeout intervals configured. After some time, one model's publish timeout handler is called....
Hi to everybody,
I'm developing over nRF5 SDK v. 3.2.0 a Zigbee node in router role. In my network I've four of my nodes plus several commercial led light driver and a coordinator...
Hello!
I am setting up SEGGER on my mac. Completed all the steps in Getting Started Assistant. But in the last step at "Set up a project in SEGGER Embedded Studio" where...
Hi,
I am evaluating a project where I want to run light switch on nrf52840. This is supposed to support mentioned protocols - BLE Mesh, Thread and Zigbee, but NOT concurrently...
I plan to connect an nRF52810 bluetooth output to a Johansen Tech 2450AT07A0100 chip antenna via a Johansen 2450FM07A0029 impedance matching chip. Do you have a BT SIG approved...
Hi, I am using nRf9160 with last sdk (master branch) and Segger Embedded studio V4.52. When I compile and run any program everything works, but when I try to debug the program...
