Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I am using SDK 15.3, SES 4.3 and SD 130. I've added the saadc example code into my code which is comprised of the ble_central, nordic UART and saadc.
I've changed the timer...
Hi!
I just got the Thingy:91 to play around with, but the modem firmware is old. Is it possible to update the modem firmware using USB and the Programmer software? The ...
Hello,
I am trying to build a Zephyr application for the Thingy91 which uses the I2S module to receive audio data from an external microphone and sends this data via BLE...
Hello,
i would like to point out what i think is a missing dependency in file "include/modem/modem_info.h". At row 187 there is:
but at_param_type is not declared in...
I am going through the steps for building a secure bootloader
https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
However I...
Hi,
I am trying to better understand the eSIM provisioning process. I want to verify that the IMSI changes to a local profile after the first registration with the provisioning...
Hi Nordic Devzone readers,
Recently I've picked up a NRF9160DK and have tried to program my own user program onto it. This will consistently fail unless I hold the reset...
Hi,
I am using the BMD340 module from Rigado. The module is connected to a raspberry compute module via UART. The design implemented is the “CLI co-processor design” where...
I have downloaded ADC example to the board nrf51422. I could not figure out how to give analog input and view digital output. please help. Thanks in advance...
To the kind attention of Nordic support team,
I'm using sdk 15.2, I'm working on usb hid composite example, and I modified it to have it scanning a big input keyboard matrix...
Hi,
As we know,we can modify the Mesh params though the config model, but when we actually installing and deploying ,If we want to improve the reliability of the Mesh network...
I try to bring an old Project (2017) back to life and use the new SDK 16
the Code usese BLE_GAP_TIMEOUT_SRC_ADVERTISING, but that is removed in the new SDK version,
what...
51822
SDK11
Can we change the advertise interval after 51822 started? I need to change the interval to lower / higher based on the user phone. For example, if its IOS...
How does Broadcast characteristic property of GATT can allow BLE observers devices to read the data without being connected with the device? Does this mean we share data without...
We recently ported to the nRF52832 and our electrical engineer had to make a couple changes from the reference design due to space constraints. The port has worked well during...
