I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Dear Nordic team,
I am currently working with the Thingy:91X (nRF9151) and nRF Connect SDK v2.9.0 , and I am attempting to run the official ECDSA sample from your documentation...
Hello,
Does the nrf_oberon library support the nRF54L series parts? In the technical documentation, it appears that M33 parts are supported: https://docs.nordicsemi.com...
We are currently using an nRF53 in our plant sensor project, where we need to be able to enter sleep mode and be woken up via RTC and GPIO interrupt. Since the nRF53 does...
Greetings,
we developed a custom board with a NRF9160 last year to be used with NB-IoT (LTE-M as Fallback) to communicate over HTTPS with our Servers. Now this worked quite...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
Hello.
I keep trying to control my GoPro camera via BLE. At first I tried to do it using the old sdk, but it didn't work ( devzone.nordicsemi.com/.../gopro-control-over...
Hello! I have a Nordic Power Profiler Kit 2 that I am using to make measurements on a project. The issue I am having is I get an error message when trying to connect the kit...
Hello All
We are trying to integrate ST7305 driver with NRF connecct SDK and are unable to get the driver to work using the extrnal module method mentioned in the NCS Intermediate...
My device tree overlay GPIO section looks like this:
Note that I repurposing a GPIO that was used for an LED in the board's device tree file. Also note that node numbers...
Hello,
I am using the nfc_system_off example code to evaluate the characteristics of power off mode.
Current measurement is done by following the instruction shown in...
I am trying to use Health SRV and Health CLI to check if there are any errors in the nodes. I have successfully transmitted the fault codes, but there are still many questions...
Hello
I created the out of tree sample sensor application with SDK 2.6.2 and it built just fine However it builds only when it is inside the sdk that was pulled when I selected...
Hey everyone. I am having an issue reading the WHO_AM_I register from the stm lsm6dsv16x. I am using the spi1 configuration as shown in the academy classes. I have very short...
I am using an nRF52840 USB dongle to sniff some Zigbee packets for a product I am developing. I am trying to use Wireshark to decode the messages shared. I followed the steps...
Hi,
I'm using nRF9160DK with SDKs v3.0.0
I am trying to use A-GPS with nRFCloud REST. I used the location example and it works correctly. The documentation states that...
