Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hello
I want to setting up DFU in my project. I followed this document :
link text
I'm using IAR EWARM and nRF51_SDK_8.0.0 and "nRF51_SDK_8.0.0\examples\dfu\bootloader...
Dear all,
I have written some code that controls the SPIS and allows it to transfer data as if it were a master. I am generating the SPIS clock from one timer, and I am...
Hi everyone
for my application I must use the Bluegiga dongle like central (PC side) and nRF51822 for peripheral (hardware side).
So I implemented cable replacement app...
I feel stupid asking this question, it should be documented in the standard and the code but I have looked and googled with no luck.
I want to populate the ble_rscs_meas_t...
What are the considerations when choosing between using an external 32.768 kHz oscillator and just using the internal RC oscillator as the low frequency clock source?
Here...
Hi,
Does anyone know if there is windows (8.0) visual c++ command in the BluetoothGatt functions to use the memory request event with S110?
Many Thanks
Hello,
I would like to develop a quick prototype with nRF51/52 however do not have experience in designing apps. I have seen the example apps and was wondering whether...
Hi,
your Central is able to hold 8 connections with peripherals. Perhaps someone is able to explain how more than one connection is handled? If only one Central is connected...
My Project:
I want to control 2 outputs on the nRF51DK from my mobile device(Android & iOS). Its a simple program:
left button is pressed -> PIN 21 High / left button...
Hi ,
I am planning to buy nRF51 USB Dongle(S120 SoftDevice or S130 SoftDevice) to discover BLE devices and to communicate bi-directional. I am planning to develop C# in...
I am using
nrfgo studio ver 1.20.0.2
s132_nrf52_1.0.0-3.alpha_softdevice.hex
nrf52832_xx_aa_s132.hex supplied by Nordic (ble_app_template)
emIDE 2.20
The firmware runs...
Hi,
with the pstorage library, is it possible to store data at a specific flash address?
The background of the question is that I would like to store data in flash, and...
Hi,
I am using PWM for a buzzer. It is working, but the current consumption is always 300uA when PWM is not in use. This minimal current consumption appears right after...
1: my nrf51 SDK board not work , I replace the USB control IC--ATSAM3U1C-AU(the old is ATSAM3U2CA-AU),can you send me the firmwair of JLINK with this IC and the contacted...
Hi Nordic,
I want to know, how the button_push_sequence works on case of handling different events at different button_push sequence like... (--nrf51-ble-app-lbs--)
...
