Hi,
If the following function is used, how to solve this error:
#include <nrfx_reset_reason.h>
void check_and_clear_reset_reason ( void )
{
// 获取复位原因
uint32_t...
2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the nRF Connect...
Hi, i try to understand how to use power down modes. But i have a problem in the example ( nRF24LE1 REGISTER RETENTION TIMER ON ).
while(1)
{
// Register retention mode...
Hello,
I've created own characteristic and send it from proprietary board acting as peripheral to the Client in form of notifications. I use sd_ble_gatts_hvx() function...
Does anyone know of a good tool(s) for prototyping proprietary services and characteristics for App development? Our App dev team is ahaead of our firmware team and they want...
Hi,
I'd like to know how tp estimate of the best "timing accuracy" I could expect to achieve between an iOS device and a peripheral device. The objective is to make a specific...
Hi,
In my application I want to communicate nRF24L01+ with nRF51822 with dynamic length. Some settings are:
In nRF24L01+ side (reference: devzone.nordicsemi.com/.../)...
Hi,
Now I use these fun in ANT SD210 like below:
void MyFlashWrite(ble_ant_csc_t* cscdata)
{
uint32_t addr;
uint32_t patwr[3];
uint32_t pg_size;
uint32_t pg_num;...
what information does the nrfjprog.exe write to UICR(User Information Configuration Registers) register??
==========Tutorial of Flashing dfu bootloader to the nRF51 DK...
I want to use the ble sniffer to capture two peripherals connected to the master control panel.
with the ble sniffer I can only select one peripheral for capturing packets...
Hey there, I've posted this issue on the tutorial website and I came across a post stating that posting here will get me a quicker response. Here's my problem, when I tried...
In my application need to nrf8001 connect(bond) to e phone in a specific duration (for example 1 hours )and then disconnect and in one hour later bond again. In this duration...
Hi,
I am developing a Heart Rate application.
I need to ensure that i am flashing correct softdevice file through my application.
How can i do that?
Regards,
Sum...
Hi,all
i study DFU step by step according this link devzone.nordicsemi.com/.../a00076.html,but failed at step 8.my peripheral advertising as Nordic_HRM not dfuTag.
Can someone...
hi,
I used previously nrfjprog version 5 to program SD+APP+BL with --dfu flag and I can perform OTA DFU.
Now with version 7 there is no --dfu flag anymore and if I try...
Same question as devzone.nordicsemi.com/.../
What needs to change for a gcc setup in the compile flags.
If that helps, some of the flags I have now include:
-mfloat...
