I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
To reduce power, I'm trying to find the best approach to minimize the cpu load when sampling an accelerometer at a high rate, e.g. 1.6Khz. Is there a way to DMA a sensors...
I am writing a crc checker for the application and the softdevice . I am using a s120 version 2.0.0 it currently has a upper boundary of 0x1D000 is this a hard boundary for...
Hi everyone.
I am making an application which combines two services (ANCS and Nordic UART). I compare the advertising_init() function from the two provided examples (ble_app_ancs_c...
Hi,
I've been searching the devzone for TWI examples, and preferably an example with MPU6050. Here are a conclusion of stuff that I found, but as some of them were for...
Hi ,
I tried to upload the application firmware using OTA service through MCP, I successfully get connected and the transferring of application hex file also gets successfully...
Hi Guys,
once again, I have strange behavior of my code.
In my code I try in loop after ble_event received change PWM from 0 to 255 for my motor device. In debug logs...
Dear,
Please, could help me ?
My knowledge in RF is basic.
I am developing a system to use 8 RF channels (nRF24L01 +) simultaneously.
I'm using Balum 2450BM14A0002...
Hi,
I’ve just ordered a few nrf51822 (from seedstudio ) and waiting for them to arrive.
They come preloaded with SoftDevice 6.0 or 7.0. with a pre-flashed OTA boot loader...
Hello, I am trying to connect a Nexus 6p running Android 6.0 to the NRF52 dev board. I have tried numerous ble examples in the SDK, but nothing ever appears in the nRF Master...
So if I start a program in debug mode some zero-inited static variables are non-zero.
ldr r1, =__etext
ldr r2, =__data_start__
ldr r3, =__data_end__
subs r3, r2...
I'm attempting to use the app_trace module. I've set it up as follows:
int main(void)
{
// Setup tracing. Also sets up UART.
app_trace_init();
app_trace_log(...
Hello,
I know that this question has been asked a few times, but I am a little desperate after trying to get debug logging over the Virtual COM Port to work. Here are the...
Hi,
I've recently got some brand new nRF51 Dongle, and used nRF51 DK. The problem is that DK is not recognized by mine PC. There's actually some example program (heart...
Is that bad to call RTT functions if there is no SEGGER connected?
I mean, if there is no RTT viewer connected, what the RTT library does with the message to transmit?...
