NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hi, In your documentation you specify the maximum CPU temperature 85 DegC.
What problems could one expect after this point?
How much safety margain du you have on this number...
I'be been reading over and over the datasheet but cannot see how to dissable Enhanced ShockBurst features for my application which only requires basic one way radio.
I...
Hello,
I'm trying to program that module, but i can't do it correctly.
I'm using a program that works fine in nrf51 DK, but when I program this in ptr5518 my smartphone...
I want to port either the S210 experimental DFU over ANT_FS to serial DFU or the S110 dual bank serial DFU project to be S210 compatible.
I'm using S210 V4 and SDK 8
...
I would like to connect more than 8 devices to a single host. Therefore I would have to set the same role to multiple devices.
What are the implications of using the same...
HI,
I have some problems with the function sd_ble_gap_scan_stop(). I want to stop scanning into the RTC1 event handler but when I use this function (sd_ble_gap_scan_stop...
HI:
i have a question.if i use 51822 to connect other ble(ti or csr) ,could that be achieved.i have used ti dongle to scan 51822,but can't found 51822 device.if 51822 connect...
Hello,
In our project we use HID service. The difference between our HID and standart HID is that we use our own UUIDs. Our report charactestics include Report Refernces...
I'm having trouble compiling the pc-ble-driver ( github.com/.../pc-ble-driver) on windows. Some help debugging the problem would be greatly appreciated. It might be an issue...
Hi,
I am using SD110 V8.0.0, SDK 8 and chipset nRF51822 QFAC.
Sometimes my app get assert error from file A\a with random error code and 0x0000000 line number. How to...
I use the software 1.0.1.478.0 release. Is it functional with V1.0.4 plugin ?
When I generated the following message code is displayed :
" Nordic Semiconductor nRF51 plugin...
I am trying to setup a multiceiver scenario with the nrf24l01+ with three transmitters (PTX1,PTX2 and PTX3) and one receiver (PRX) with enhanced shockburst but I am having...
Hi,
I'm trying to use winbond spi flash (w25q64fv)
but i have a problem with spi as you can see in below image clock stop before receiving data from spi flash, do you...
Hi,
i use for debugging propose JLinkRTTViewer on OS X Terminal. It works fine but i wanted to use Colored Terminal output, like it is possible in windows rtf viewer application...
