Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I would need to change a timer into single shot mode. My code is as follows:
static const nrf_drv_timer_t m_timer = NRF_DRV_TIMER_INSTANCE(MY_SAMPLE_TIMER);
nrf_drv_timer_init...
using S130, SDK11,
CANNOT work the two heart rate sensors which have the different deivce name ?
when it connected the heart rate sensor A and eveything is OK.
but...
Hello,
I want to use nRF52832 at 2V. But I am not sure what would be the current consumption of radio during transmission and reception with DCDC regulator on. In datasheet...
Hi, after some research and reading several posts (especially this one ), I am still confused about the Flash endurance on the nRF52.
In the product specification for the...
Hi,
I developed a device and I ship this devices to custemers. Now I want to update firmware of this devices with user friendly app. Is there any app updating app for customers...
Hi,
I scan for nrf51 hrs peripheral devices.
It discover them but they have a static pass-code, how can i pair to them from my central device?
I use SDK11 hrs_c s130...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
I am trying the ANT-OTA DFU Update using two nr51422 pca 10028 board. One is sending Transmission messages in the CHANNEL_TYPE_MASTER mode, while the other is receiving Messages...
Hello, I'm a beginner for nRF51822, now my status is sticking on those SDK_11.0.0 BLE examples, while I could successfully running non-BLE (such as examples of bsp/uart)....
ElfApp.zip This attached application is based on Nrf_uart demo app.
It works fine under Android 5.0 and 4.4 smartphone. When I click the connect button, it shows the info...
Hi,
I'm on the project where I use SoftDevice s132 on my own devBoard with nrf52 chip.
I know for Connection Interval and other parameters that determin BLE communication...
I am using nrf51822 as a central device that is trying to connect a peripheral device nrf8001.
I want to build communication bewteen them and use nrf51822 to receive the...
Hi,
I have a small question regarding flash write/erase cycles and I was unable to find a clear answer.
I can see in NRF52 specs:
Flash write/erase cycles: 10...
Hi,
I've been trying to get DFU updates working on my device for a while now... I've got the single-bank bootloader compiled and seemingly working (and a combined hex file...
