I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
Hello,
My application is really close to the example named BLE relay example in the DK. We could start from this example and adapt it to our needs. The problem is that this...
I have the Adafruit Sniffer which is based on the nRF51822 Bluefruit LE Friend, which contains the Raytac MDBT40 . After searching and finding the CP2104 drivers, I can speak...
I have been reading the forum and there seems to be differing advice to use Timers or RTC, since TIMER0 is used by the soft device, so it could cause issues since the SAADC...
Hi All:
i have a trouble, i need Coexistence mesh sdk 2.0.0 provisioner and nrf SDK 15 template. but mesh not work when nrf SDK 15 run advertising_start(erase_bonds);
...
I'm working with nrf24l01 module and use it in BLE beacon mode.
My main question is how can I decrease the visibility range to 10 - 20 santimeters?
(by some schematic...
Hi Support team,
My search for nrf8001 port to Arm-m3 landed me on a thread , where the support personnel has provided a link for a port to lpc1769 in the last comment....
Hi,
I would like to add sensor data in mesh network to be able to send data in certain intervals. How is it possible when I create a sensor model for mesh client and server...
Hello. I have a nRF52832 DK and I'm trying to modify the SPI example code found here:
/nRF5_SDK_15.0.0/nRF5_SDK_15.0.0_a53641a/examples/peripheral/spi
I'm using the nRF52832...
Hello Guys,
I have brought this nrf52840 to try BLE mesh. I tried connecting it to the PC and it was working fine, later I tried dumping the file into the board through...
Hey Nordic and co-nordic developpers,
Just to show some capabilities here at work I want to compile and run the mesh demo on the 10 Thingy52's we have here. I am currently...
Hi Nordic,
Could you please help me ! This is an urgent matter!
Based on this discussion , there is an error rate of actual baudrate comparing with the desired one.
...
Hello everyone,
I'm trying to use the new SDK 15.0.0 and the S140 soft device V6.0.0. I would like to use the LE CODED physical layer and set my TX output power, but when...
Why did the softdevice handler's API change?
sorry for a general question. I used SDK 13. and Now, I am porting my software to SDK 15. So, I have simple question. Why did...
My application is based of the UART example, I have a repeating app timer that fires every 5 min's to do some tasks, I also utilise single fire timers (initiated for events...
Ok, so I am using nRF52DK and trying to figure out to how to send up to 6 packets of data from custom service that sends 6 16bit values per packet. When I send one packet...
